Table of Contents
Advertisement
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Note:
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of the FCC rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual.
If such changes or modifications should be made, you could be required to stop operation of the
equipment.
Notice:
If static electricity or electromagnetism causes data transfer to discontinue midway (fail), restart the
application or disconnect and connect the communication cable (USB, etc.) again.
EN-1
Advertisement
Table of Contents
Related Manuals for Sanyo VPC-T700
Summary of Contents for Sanyo VPC-T700
-
Page 1: Fcc Statement
FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. -
Page 2: Trademark Information
TRADEMARK INFORMATION ® ® Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Pentium ® is a registered trademark of Intel Corporation. ® Macintosh is a trademark of Apple Computer, Inc. is a trademark. Other names and products may be trademarks or registered trademarks of their respective owners. -
Page 3: Safety Instructions
Safety Instructions Read and understand all Warnings and Cautions before using this product. WARNING If foreign objects or water have entered the camera, turn the power OFF and remove the battery and the AC power adapter. Continued use in this state might cause fire or electric shock. Consult the store of purchase. If the camera has fallen or its case has been damaged, turn the power OFF and remove the battery and the AC power adapter. - Page 4 CAUTION Insert the battery paying careful attention to the polarity (+ or –) of the terminals. Inserting the battery with its polarities inverted might cause fire and injury, or damage to the surrounding areas due to the battery rupturing or leaking. Do not fire the flash close to anyone’s eyes.
- Page 5 Warning: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE FOR AMERICAN USERS The following advisory is included in accordance with the laws of the State of California (USA): WARNING: This product contains chemicals, including lead, known to the States of California to cause cancer, birth defects or other reproductive harm.
- Page 6 This symbol mark and recycle system apply to EU countries and do not apply to countries in other areas of the world. Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and reused.
-
Page 7: Fcc Information
“Troubleshooting”. Declaration of Conformity Model number: VPC-T700 Trade Name: SANYO Responsible party: SANYO FISHER COMPANY Address: 21605 Plummer Street Chatsworth, California 91311 Telephone No.: (818) 998-7322 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two... -
Page 8: Notes On Battery Usage
Notes on Battery Usage When you use the battery, carefully read and strictly observe the Safety Instructions and the notes described below: Use only the specified battery (3.7V). Avoid using the battery in extremely cold environments as low temperatures can shorten the battery life and reduce camera performance. -
Page 9: Table Of Contents
CONTENTS INTRODUCTION Overview Package Contents GETTING TO KNOW THE CAMERA Front View Rear View LCD Monitor Icons GETTING STARTED Attaching the Camera Strap Inserting and Removing the Battery Charging the Battery Inserting and Removing the SD/SDHC Memory Card (Optional Accessory) Setting the Date and Time Formatting the SD/SDHC Memory Card or Internal Memory... - Page 10 CONNECTING TO A PICTBRIDGE COMPLIANT PRINTER TRANSFERRING RECORDED IMAGES AND VIDEOS TO YOUR COMPUTER 57 Connecting the Camera to Your Computer 58 Downloading Images and Video Files USING THE CAMERA AS A PC CAMERA 59 Install the PC Camera Driver 60 Connect the Camera to Your Computer 60 Run Your Application Software (i.e.
-
Page 11: Introduction
INTRODUCTION Overview Congratulations on your purchase of the new digital camera. Capturing high-quality digital images is fast and easy with this state-of-the-art smart camera. Equipped with a 7.0 megapixel CCD, this camera is capable of capturing images with a resolution of up to 3072 x 2304 pixels. -
Page 12: Package Contents
Package Contents Carefully unpack your camera and ensure that you have the following items. Common Product Components: Digital camera User’s manual Software CD-ROM USB cable AV cable Camera strap Camera pouch AC power adapter Adapter converter (for “DC Jack to mini USB cable”) Rechargeable lithium-ion battery Common (Optional) Accessories: SD/SDHC memory card... -
Page 13: Getting To Know The Camera
GETTING TO KNOW THE CAMERA Front View Shutter button ON/OFF button Self-timer LED Flash Lens Microphone EN-13... -
Page 14: Rear View
Rear View LCD monitor Mode switch Capture mode Video mode Playback mode DISPLAY button Status LED Zoom in button Zoom out button MENU button EN-14 2 3 4 Erase button Speaker SET /Direction button 10. PC/AV terminal 11. Strap holder 12. - Page 15 SET /Direction button 5. SET button button Focus button button Flash button button Self-timer button button Exposure/ Backlight correction button EN-15...
-
Page 16: Lcd Monitor Icons
LCD Monitor Icons Capture mode [ 1. Zoom status 2. Voice memo 3. Remaining battery status Full battery power Medium battery power Low battery power ] No battery power ] AC adapter icon (if used) 4. Flash mode [ Blank] Auto Flash ] Red-eye Reduction Forced Flash ] Flash Off... -
Page 17: Still Image Playback
Video mode [ 1. [ ] Video mode 2. Zoom status 3. Remaining battery status 4. Image size 5. Possible recording time / elapsed time 6. Quality 7. Recording indicator 8. Self-timer icon 9. Focus icon Playback mode [ ] -Still image playback 1. -
Page 18: Getting Started
GETTING STARTED Attaching the Camera Strap Attach the camera strap as shown in the illustration. Inserting and Removing the Battery We highly recommend using specified rechargeable lithium-ion battery (3.7V) to fully demonstrate this camera’s function. Charge the battery before using the camera. Make sure that the power of the camera is off before inserting or removing the battery. -
Page 19: Charging The Battery
Charging the Battery The AC power adapter may charge the battery or operate the camera as power supply. Make sure that the power of the camera is off and then insert the battery before starting. 1. Connect one end of the adapter converter to the end of the AC power adapter. -
Page 20: Inserting And Removing The Sd/Sdhc
Inserting and Removing the SD/SDHC Memory Card (Optional Accessory) The digital camera comes with 32 MB of internal memory (approx. 27 MB for image storage), allowing you to store captured still images or video clips in the digital camera. However, you can also expand the memory capacity by using an SD/SDHC memory card so that you can store more files. -
Page 21: Setting The Date And Time
Setting the Date and Time The date/time needs to be set if/when: Camera is turned on for the first time. Camera is turned on after leaving the camera without the battery for an extended period of time. When the date and time information is not displayed on the LCD monitor, follow these steps to set the correct date and time. -
Page 22: Formatting The Sd/Sdhc Memory Card
Formatting the SD/SDHC Memory Card or Internal Memory This utility formats the internal memory (or memory card) and erases all stored images and data. 1. Slide the mode switch to [ 2. Press the MENU button and select [Setup] menu with 3. -
Page 23: Setting Image Resolution And Quality
Setting Image Resolution and Quality Resolution and quality settings determine the pixel size (dimension), image file size, and compression ratio for your images. These settings affect the number of images that can be stored. As you get to know the camera, it is recommended that you try each quality and resolution setting to get an appreciation for the effects that these settings will have on your images. - Page 24 Possible number of shots (still image) The table shows the approximate shots that you can capture at each setting based on the capacity of the internal memory and the SD/SDHC memory card. Internal Size Quality Memory Fine Standard 3072 x 2304 Economy Fine Standard...
- Page 25 Possible recording time / sec (video clip) Internal Size Quality Memory 00:00:12 Fine Standard 00:00:14 640 x 480 00:00:41 Fine 00:00:46 Standard 320 x 240 If your memory card is not high speed write (over 2MB/Sec for random write), it will cause video clip auto stop or unexpected results.
-
Page 26: Photography Mode
PHOTOGRAPHY MODE ] Capture Mode Your camera is equipped with a 2.5" full color LTPS-TFT LCD monitor to help you compose images, playback recorded images/video clips or adjust menu settings. 1. Press the ON/OFF button to turn the power on. The status LED lights green and the camera is initiated. -
Page 27: Recording Voice Memos
Recording Voice Memos A voice memo can be recorded once for 30 seconds at still image mode immediately following a still image captured. 1. Slide the mode switch to [ 2. Press the MENU button, and select the [Function] menu with button. -
Page 28: Using The Digital Zoom
Using the Digital Zoom Using a combination of 3 times optical zoom and 4 times digital zoom permits zoom photography of up to 12 times to suit the subject and the distance. The digital zoom is a compelling feature, the more an image is enlarged (zoomed), the more pixelated (grainier) the image will appear. -
Page 29: Setting The Flash
Setting the Flash Set the flash for capturing images. The flash firing mode can be set to suit for the photographic conditions. 1. Slide the mode switch to [ 2. Toggle the button to select the desired flash mode. The available flash settings in different photography modes: Flash mode [ Blank ] Auto Flash ] Red-eye Reduction... -
Page 30: Setting The Focus
Setting the Focus Images can be captured with the distance to the subject set by auto focus, [ 1. Slide the mode switch to [ 2. Toggle the button to select the desired focus mode. The table below will help you choose the appropriate focus mode: Focus mode Description [ Blank]Auto Focus... -
Page 31: Setting The Self-Timer
Setting the Self-timer This setting allows images to be captured with the self-timer. 1. Slide the mode switch to [ 2. Toggle the button to select the setting. For the [ ] mode. OFF [ 10s] 10 sec. 10+2s ] 10+2 sec. For the [ ] mode. -
Page 32: Exposure Compensation/Backlight
Exposure Compensation/Backlight Correction Images can be captured with the overall screen intentionally made brighter or darker. These settings are used when a suitable brightness (exposure) cannot otherwise be obtained in circumstance where the difference in brightness between the subject and the background (the contrast) is large, or when the subject that you want to photograph is very small within the screen. -
Page 33: Setting The Scene Mode
Setting the Scene Mode By simply selecting one of the following 21 modes, you can capture the image with most appropriate settings. 1. Slide the mode switch to [ a. Press the MENU button. b. Select [Scene Mode] with the Select the desired scene mode with the 2. - Page 34 Scene mode Description [TEXT] Text Select this mode when you want to capture an image that contains black and white subjects like printed documents. ] Sunset Select this mode when you want to capture images of a beautiful sunset shot that vividly captures beautiful red colors.
-
Page 35: Setting The Panorama Mode
Setting the Panorama Mode This mode is designed to make it easier to take a series of shots then stitch them together with software to make a single image. You can capture a photographic subject that won’t fit into a single frame, such as a landscape, and stitch it together later with a program such as Cool 360 or Photoshop application. -
Page 36: Playback Mode
] PLAYBACK MODE Playing Back Still Images You can play back the still images on an LCD monitor. 1. Slide the mode switch to [ The last image appears on the screen. 2. The images can be fed in reverse or fed forward with the To view the previous image, press the To view the next image, press the Pressing the... -
Page 37: Playing Back Video Clips
Playing Back Video Clips You can play back video clips recorded on the LCD monitor. You can also play back sound if you recording with the audio. 1. Slide the mode switch to [ The last image appears on the screen. 2. -
Page 38: Attaching Voice Memos
Attaching Voice Memos A maximum of 30 seconds of audio can be recorded like a memo for captured still images. The voice memo can be recorded only once. 1. Slide the mode switch to [ The last image appears on the screen. 2. -
Page 39: Zoom Playback
Zoom Playback This mode also allows you to enlarge your image on the selected portion of the image to check for small details. 1. Slide the mode switch to [ 2. Press the buttons to select the image you want to enlarge. -
Page 40: Protecting Images
Protecting Images Set the data to read-only to prevent images from being erased by mistake. Protecting Images 1. Slide the mode switch to [ 2. Select the image that you want to protect with the buttons. 3. Press the MENU button. The playback menu is displayed. - Page 41 Canceling the Protection To cancel protection for only one image, display the image that you want to remove the image protection. 1. Select [Protect] with the 2. Select [Single] or [All] with the 3. Select [Cancel Protect] with the The removal of image protection is executed and the camera returns to the playback mode. Protecting multiple images simultaneously 1.
-
Page 42: Dpof Settings
DPOF Settings DPOF is the abbreviation for Digital Print Order Format, which allows you to embed printing information on your memory card. You can select the images to be printed and how many prints to make with the DPOF menu in the camera and insert the memory card to the card compatible printer. When the printer starts printing, it will read the embedded information on the memory card and print the specified images. -
Page 43: Resizing An Image
This creates a file containing the DPOF information, and when the operation is finished, the screen returns to the playback mode. The DPOF icon [ ] is displayed on each image that has set up DPOF settings. The date that is printed on the image is the date set on the camera. To print the correct date on the image, set the date on the camera before you capture the image. -
Page 44: Erasing Images
Erasing Images Erasing at Photography Mode (Quick Delete Function) The quick delete function enables you to delete the last-captured image during capture. 1. Slide the mode switch to [ 2. Press the button. The last image and quick delete menu appear on the screen. - Page 45 5. Select [Execute] with the To not erase, select [Cancel], and press the SET button. Deleting an image will not affect sequential image numbering. For example, if you delete image number 240, the next captured image will be numbered 241 even though 240 no longer exists.
-
Page 46: Menu Options
MENU OPTIONS Capture Menu (Capture) This menu is for the basic settings to be used when capturing still images. 1. Slide the mode switch to [ 2. Press the MENU button. [Capture] menu is displayed. 3. Select the desired [Capture] option item with the buttons, and press the SET button to enter its respective menu. - Page 47 Saturation This sets the saturation of the image that will be captured. * High / Normal / Low White Balance This sets the white balance capturing under a variety of lighting conditions and permits images to be captured that approach the conditions that are seen by the human eye. * [ Blank ] Auto Incandescent Fluorescent 1...
-
Page 48: Capture Menu (Function)
Capture Menu (Function) 1. Slide the mode switch to [ 2. Press the MENU button, and select the [Function] menu with button. [Function] menu is displayed. 3. Select the desired [Function] option item with the buttons, and press the SET button to enter its respective menu. - Page 49 LCD Bright. Select a brightness level for the LCD monitor. The LCD becomes brighter with the button. The adjustment range is from -5 to +5. Digital Zoom This sets whether or not to use digital zoom at the time of photography. * On / Off When [Voice Memo] is set to [On], the preview setting is also fixed at [On].
-
Page 50: Video Menu (Capture)
Video Menu (Capture) This menu is for the basic settings to be used when recording video clips. 1. Slide the mode switch to [ 2. Press the MENU button. [Capture] menu is displayed. 3. Select the desired [Capture] option item with the and press the SET button to enter its respective menu. -
Page 51: Video Menu (Function)
Video Menu (Function) 1. Slide the mode switch to [ 2. Press the MENU button, and select the [Function] menu with button. [Function] menu is displayed. 3. Select the desired [Function] option item with the buttons, and press the SET button to enter its respective menu. -
Page 52: Playback Menu
Playback Menu In the [ ] mode, set which settings are to be used for playback. 1. Slide the mode switch to [ 2. Press the MENU button. The playback menu is displayed. 3. Select the desired option item with the press the SET button to enter its respective menu. -
Page 53: Setup Menu (In Photography Mode)
Setup Menu (In Photography Mode) Set your camera ’ s operating environment. 1. Slide the mode switch to [ 2. Press the MENU button, and select the [Setup] menu with button. [Setup] menu is displayed. 3. Select the desired [Setup] option item with the and press the SET button to enter its respective menu. -
Page 54: Setup Menu (In Playback Mode)
Setup Menu (In Playback Mode) 1. Slide the mode switch to [ 2. Press the MENU button, and select the [Setup] menu with button. [Setup] menu is displayed. 3. Select the desired [Setup] option item with the and press the SET button to enter its respective menu. 4. -
Page 55: Connecting To A Pictbridge Compliant Printer
CONNECTING TO A PICTBRIDGE COMPLIANT PRINTER If a printer that supports PictBridge is available, images can be printed by connecting the digital still camera directly to the PictBridge-compatible printer without using a computer. Connecting the camera to the printer Connect one end of the USB cable to the PC/AV terminal of the camera. Connect the other end of the USB cable to the USB port on the printer. - Page 56 3. If you select [Select] in the previous step, the figure shown on the right hand side will appear. Select the image that you want to print with the Select the [Print Num] (up to 99) with the After selecting the desired image and printing number, press the SET button to confirm.
-
Page 57: Transferring Recorded Images And Videos To Your Computer
TRANSFERRING RECORDED IMAGES AND VIDEOS TO YOUR COMPUTER System Requirements Windows Pentium III 600 MHz or higher Windows 2000/XP/Vista 64MB RAM 128MB hard disk space CD-ROM drive Available USB port Connecting the Camera to Your Computer 1. Connect one end of the USB cable to the PC/AV terminal of the camera. -
Page 58: Downloading Images And Video Files
Downloading Images and Video Files When the camera is turned on and connected to your computer, it is considered to be a disk drive, just like a floppy disk or CD. You can download (transfer) images by copying them from the “Removable disk”... -
Page 59: Using The Camera As A Pc Camera
USING THE CAMERA AS A PC CAMERA Your camera can act as a PC camera, which allows you to videoconference with business associates, or have a real-time conversation with friends or family. Video conferencing (or video editing) software is not included with the camera. This mode is not supported for Mac. - Page 60 Connect the Camera to Your Computer 1. Connect one end of the USB cable to the PC/AV terminal on the camera. 2. Connect the other end of the USB cable to an available USB port on your computer. 3. Turn on your camera. The [USB] screen appears.
-
Page 61: Editing Software Installation
EDITING SOFTWARE INSTALLATION Installing Photo Explorer ® Ulead Photo Explorer provides a simple and efficient way to transfer, browse, modify and distribute digital media. Acquire photos, video or sound clips from various digital device types and easily browse or add personal descriptions; make timely modifications; or distribute the media through the medium of your choice: E-mail, Print, Slideshow Presentations. -
Page 62: Installing Cool 360
Installing Cool 360 ® Ulead COOL 360™ quickly and easily allows photo editing consumers to transform a series of photos into 360 or wide-angle panoramic scenes for an immersive viewing experience. COOL 360’s intuitive interface and easy-to-use wizard deliver great-looking panoramas fast while advanced warping, blending and alignment tools ensure excellent results. -
Page 63: Camera Specifications
CAMERA SPECIFICATIONS Item Image sensor Image resolution LCD monitor Recording media Compression format File format Lens Focus range Shutter speed Digital zoom Flash effective range Terminal Power supply Dimensions Weight *Design and specifications are subject to change without notice. Description 1/2.5”... -
Page 64: Troubleshooting
TROUBLESHOOTING Refer to the symptoms and solutions listed below before sending the camera for repairs. If the problem persists, contact your local reseller or service center. Power Supply Cause Symptom The battery in not inserted. The power does not come The battery is exhausted. - Page 65 Shooting Symptom Cause The battery is running low. The power is not on. The camera is not in shooting mode. The shutter button is not pressed all the way down. The memory card does not have any free capacity. Even if I press the shutter End of memory card life.
-
Page 66: Other Problems
Playback Symptom Cause Cannot playback. It is not set to playback mode. The contents of memory You played back a memory card that card cannot be played back. was not formatted by this device. The file is protected. You played back a memory card that Files cannot be deleted.