Table of Contents Table of Contents ........................1 Figure 1. Schematic Diagram ......................2 Figure 2. Basic Circuit Diagram ......................3 Failure & Troubleshooting of Power Supply ..................4 Troubleshooting and service of the Loader ................... 4-5 Troubleshooting and service of Decoding Part ..................5 Troubleshooting and service of Video Part ....................6 Troubleshooting and service of Audio Part ....................6 Troubleshooting and service of KARAOKE Part ..................
Page 3
Figure 1 Schematic Diagram(TD-F61/F62/F63/F70) AV BOARD A B V O ARD CON101 3.3V POWER -24V MAIN BOARD BOARD MAIN BOARD GND/VSDA0 PCON CON301 VSDA VSCK VSTB -24V PCON FRONT BOARD TD-F62/63/F50 TD-F61/F70/F71 KARAOKE KARAOKE BOARD DVD LOAD BOARD D LO V D A D...
Page 4
Figure 2 Basic Circuit Diagram MT1336 VIDEO LPF DVD LOAD VIDEO & D LO V A D D & DRIVE DRIVE 2402 VIDEO VIDEO D/A SPDIF SPDIF OUT EEPROM CS4954/4955 CS4954/4955 MT1369 2*16Mbit WM8746 WM8746 MC4558 MC4558 SDRAM AUDIO D/A AUDIO AMP&LPF DECODER&SERVO AUDIO...
a. Principle of power supply operating Adopts switched-mode power supply module TOP233Y of TOPSWITCH company, it can protect itself from over current, overheating, and short-circuit, etc. This circuitry mainly stabilizes at +5V, and fluctuates within a permissible range, such as +5V, VA+, VA-, +3.3V and -24V. Please pay attention to the high voltage inside the white paint of PCB while repairing.
pole of Q1 and Q2, and whether U2 and adjacent parts are damaged or weld falsely. d). If the above parts are normal and no laser emits, replace the loader. b. Read no disc a). Check whether the ribbon wire from 24P to loader is in good contact. b).
Check U10 that whether the data of pins from the 1st to the 8th, hsync and vsync signal of the 10th and 11th pins, and 27MHz signal of the 29th pin are normal, and whether C162 and R68 are normal. If not, replace U10. 2).
7. Full screen display or no display on VFD a). Full screen display on VFD is often caused by abnormal -24V bias voltage. Check whether D5, C19 and R17 are disconnected. b). If there is no display on VFD, firstly, check whether the filament lights in red. If not, and there is no 3.3V voltage difference between AC1 and AC2, check whether D6, C9 and R21 are damaged.
Output schematic circuit CN101 Svideo_Y 470R 10uF/16v 470R CVBS 10uF/16v Svideo_C 100P 100P Cr/B MUTE MUTE 9014C Cb/R 9014C 470R 470R SPDIF SUB1 5.1CH MUTE SUB1 10uF/16v 470R 470R 10uF/16v 100P MUTE 100P 470R 9014C con20(1.25) MUTE 9014C 470R A U D I O P S C A N O U T AUDIO PSCAN...
Page 17
Power schematic circuit CN401 HEADER D408-NU FUSE401 C401 TR401 FR104 -24V T1.6A/250ac 0.1uF/250Vac NTC10R 5VSTB CON401 L401 C408 D401 D403 C412-NU PCON A I N C P UT 38mH 102/250Vac 1N4007 1N4007 R424-NU 100uF/16V RV401 C402 V A - 300V 0.1uF/250Vac V A + D402...