Do you have a question about the FGS-VC Series and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for Nidec FGS-VC Series
Page 1
364-23-099-1 FGS-VC Series Motorized Stand Operation Manual Read Manual thoroughly prior to operation. Use instrument only after reading the complete manual. Follow all safety precautions.
Safety Precautions Be sure to read the entire instruction manual thoroughly before initial set-up, operation and maintenance. The instruction manual provides three grades of safety precautions: ”Danger”, “Warning” and “Caution”. Follow these precautions. “Danger” marking indicates possible death, severe injury or fire Danger if the user disregarded.
Page 3
Attention Safety Warning fi Pull out the AC outlet for maintenance and check or unusing a long time. fi Do not plug AC connector into outlet by a wet hand. fi May cause electric shock, a fire and injury. Attention before using FGS-VC Avoid the following.
Page 4
I n d e x 1. Ahead of the use ............................ 1 1.1. Procedure from the Installation of a force gauge to the measurement........1 1.2. Confirmation of product packing ....................1 2. Names of components..........................2 3. Names and functions of the operation panel..................2 4.
Page 6
1. Ahead of the use 1.1. Procedure from the Installation of a force gauge to the measurement FGS-VC can measure various loads using NIDEC DRIVETECHNOLOGY's digital force gauges which are FGP series and FGPX series. Confirm the following procedures before use.
2. Names of components Upper limit Knob Force gauge plate Lower limit knob Emergency switch Measurement table Operation panel 3. Names and functions of the operation panel Name Description Emergency stops when pushing. Push the switch when FGS-VC becomes abnormality or hazardous situation at Emergency switch measuring.
Page 8
mode MODE key Use to change operation mode and function setting. SET key The indicated data is set when the key is pushed. START key Start to operate at the program mode. PUSH key Move to the direction of PUSH. STOP key Stop.
Page 9
4.2. Connection to the force gauge and the stand The connection and confirmation between FGS-VC and a force gauge is the following procedure. Parameter setting of the force gauge Set the following parameters. Measurement polarity: + RS232C baud rate: 19,200 bps Refer to the manual of the force gauge.
Page 29
Procedure of the initialization of the parameters 1. Turn off, wait one minute. 2. Press ZERO and SET button both, turn on in keeping to press these buttons. 7. Dimensions Upper limit FGS-100VC Force gauge: FGP, FGPX Lower limit Emergency switch Operation panel 6×φ4.5 10-32 UNF...
FGPX-0.2 to FGPX-100 FGPX-250H 9. Troubleshooting The following are general checkpoints; please call your local NIDEC DRIVETECHNOLOGY representative or contact NIDEC DRIVETECHNOLOGY Instruments directly for further assistance. Even if the power supply is turned on, Confirm the voltage of the input supply.
This warranty shall not be effective if the product has been subject to overload, misuse, negligence, or accident, or if the product has been repaired or altered outside of NIDEC DRIVETECHNOLOGY Instruments’s authorized control in any respect which in NIDEC DRIVETECHNOLOGY Instruments’s judgment, adversely affects its condition or operation.
Page 33
Please scan the QR code or access the URL below. Contact Us https://www.nidec.com/en/nidec-drivetechnology/inquiry/ Sales Offices https://www.nidec.com/en/nidec-drivetechnology/corporate/network/sales/ Copyright NIDEC DRIVE TECHNOLOGY CORPORATION. All Rights Reserved. NIDEC SHIMPO CORPORATION change its company name to NIDEC DRIVE TECHNOLOGY CORPORATION on April 1, 2023.
Need help?
Do you have a question about the FGS-VC Series and is the answer not in the manual?
Questions and answers