Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for VTech JOTBOT 5537
Summary of Contents for VTech JOTBOT 5537
- Page 1 Instruction Manual...
-
Page 2: Included In The Package
Included in the Package 1 Washable Felt-Tip Pen 1 Guidebook 15 Double-Sided JotBot™ Drawing Chips* 1 Storage Box *Two of the drawing chips are for saving codes in Code-to-Draw mode. WARNING: All packing materials such as tape, plastic sheets, packaging locks, removable tags, cable ties, cords and packaging screws are not part of this toy and should be discarded for your child’s safety. - Page 3 Features Control Panel Animated Face Speaker Power / Drawing Chip Slot Mode Switch Holder Battery Compartment Switch to either to power JotBot™ ON. Switch to power JotBot™ OFF. Press this to confirm, to start an activity or to start drawing. Command JotBot™...
-
Page 4: Battery Removal And Installation
INSTRUCTIONS BATTERY REMOVAL AND INSTALLATION 1. Make sure the unit is turned Off. 2. Find the battery cover at the bottom of the unit. Use a screwdriver to loosen the screws and then open the battery cover. 3. Remove old batteries by pulling up on one end of each battery. -
Page 5: Important Battery Information
IMPORTANT: BATTERY INFORMATION • Insert batteries with the correct polarity (+ and -). • Do not mix old and new batteries. • Do not mix alkaline, standard (carbon-zinc) or rechargeable batteries. • Only batteries of the same or equivalent type as recommended are to be used. -
Page 6: Troubleshooting
Contact Us form located under the link. Creating and developing VTech products is accompanied by a responsibility that we take very seriously. We make every effort to ensure the accuracy of the information, which forms the value of our products. -
Page 7: Getting Started
Getting Started Insert Batteries (To be done by an adult) • Locate the battery compartment at the bottom of JotBot™. • Loosen the screws of the battery cover using a screwdriver. • Insert 4 AA alkaline batteries as indicated inside the battery compartment. - Page 8 Install Pen 1-2mm • Place a scrap sheet of paper under JotBot™. • Turn On JotBot™. • Remove the cap of the bundled pen and insert it into the pen holder. • Push the pen gently down until it reaches the paper, and then release the pen.
- Page 9 Setup Paper • Prepare an 8x11" or larger sheet of paper. • Place it on a flat, level surface. Keep the paper at least 5 inches away from the edge of the surface to avoid JotBot™ from falling. • Clear any obstacles on or near the paper. Then, place JotBot™...
- Page 10 Let’s Go! Explore more ways to learn and play with the bundled Guidebook!
-
Page 11: How To Play
How to Play Learning Mode Switch to Learning mode to play with the drawing chips or let JotBot™ choose what to play. Insert a Drawing Chip for JotBot™ to Draw • Insert a chip showing the side of the object you'd like JotBot™ to draw facing outwards. - Page 12 Drawing Activities Draw Together • JotBot™ will draw something first, then children can draw on top of it using their imagination. Draw-a-Story • JotBot™ will draw and tell a story, then children can show their creativity by drawing on top to complete the drawing and story.
- Page 13 Connect the Dots • JotBot™ will draw a picture, leaving some dotted lines for children to connect to complete the drawing. Draw the Other Half • JotBot™ will draw half of a picture, children can then mirror the drawing to complete it. Cartoon Face •...
- Page 14 Maze • JotBot™ will draw a maze. Then, place JotBot™ at the entrance of the maze, with JotBot's pen tip touching the pen symbol Input the directions that JotBot™ needs to follow to go through the maze using the arrow buttons on his head. Then, press the Go button to see JotBot™...
- Page 15 Code-to-Draw JotBot™ Switch to Code-to-Draw mode to code to draw. JotBot™ • Turn so that his back is turned to you, and you can see the arrow buttons on this head. JotBot™ • Input the directions to code to move. JotBot™...
- Page 16 Fun Draw Codes JotBot™ is able to draw various interesting drawings. Look up the Fun Draw Code section of the Guidebook and code JotBot™ to draw one of these drawings. 1. To activate Fun Draw Code mode, press and hold the Go button for 3 seconds.
- Page 17 Calibration JotBot™ is ready to play out of the box. However, if JotBot™ not drawing properly after installing new batteries, follow the below procedure to calibrate JotBot™. 1. Hold the buttons for 3 seconds until you hear “Calibration”. 2. Press to start JotBot™...
-
Page 18: Volume Controls
Volume Controls To adjust the sound volume, press to decrease the volume to increase the volume. NOTE: In cases where the arrow buttons are in use, such as when in Code-to-Draw mode, the volume controls will temporarily be unavailable. Q: What type of paper should I use? A: JotBot™... - Page 19 Trade Name: VTech Model: 5537 Product Name: JotBot™ Responsible Party: VTech Electronics North America, L.L.C. Address: 1156 W. Shure Drive, Suite 200 Arlington Heights, IL 60004 Website: vtechkids.com THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:...
- Page 20 Visit our website for more information about our products, downloads, resources and more. vtechkids.com vtechkids.ca Read our complete warranty policy online at vtechkids.com/warranty vtechkids.ca/warranty TM & © 2023 VTech Holdings Limited. All rights reserved. IM-553700-005 US CA Version:0...
Need help?
Do you have a question about the JOTBOT 5537 and is the answer not in the manual?
Questions and answers