Superior Electric POWERSTAT 10C Series Instructions For Installation, Operation And Maintenance

INSTRUCTIONS
for INSTALLATION OPERATION and MAINTENANCE
The right to make
engineering refinements
on all products is reserved.
Dimensions and other
details are subject to
change.
28 SPRING LANE • SUITE 3 • FARMINGTON, CT 06032 USA
www.superiorelectric.com
ECN 96200
002105-280 REV G
INSPECTION
Your new POWERSTAT Variable Transformer has been carefully packed for
shipment. However, damage may occur in transit. After receiving a unit,
check all components (brush contact primarily) to satisfy yourself that there
is no damage. Also make sure that the dial, knob, lock-washer and mounting
nuts are in the package. The "Damage and Shortage" Instructions packed
with the unit outline the proper procedure to follow if any parts are damaged
or missing.
INSTALLATION
POWERSTAT Variable Transformers of the 10C, 10C-40 and 12C Series are
designed for mounting in the back-of-panel position only.
Single Units
The single hole mounting of single units is fast and simple. For keying to the
panel, a 1/16 inch projection is provided. To facilitate mounting, a drilling
template is supplied as part of these instructions. Actually, the drilling template
must be used only when the hole for the 1/16 inch projection is required.
PANEL DRILLING TEMPLATE
(Viewed from Knob End)
Single Units
POWERSTAT
VARIABLE TRANSFORMERS
10C, 10C-40 and 12C Series
Telephone and Fax Numbers
Telephone
Fax
Customer Service
Product Application
Toll-Free (in USA and Canada only)
860-507-2025 Telephone
860-507-2050 Fax
860-507-2025, Ext. 70782 Customer Service
860-507-2025, Ext. 72058 Product Application
To mount, proceed as follows:
1. Using the drilling template, locate the panel holes. In order for the
terminals to be on top, the template should be upright. Drill the
holes.
2. Mount the POWERSTAT Variable Transformer as shown. Mount the
unit flush to the back of the panel and the dial flush to the front. A
single nut and lockwasher hold the unit and dial in place. The knob,
when mounted on the shaft, covers the nut and lockwasher.
3. If the unit is not to be keyed to the panel, only the hole for the 3/8
inch center shaft should be drilled. The extra nut provided is placed
on the shaft between the unit and the back of the panel. Otherwise
the mounting is as explained above.
Ganged Assemblies
Ganged units require four panel holes for mounting. Three are needed
for the mounting bolts and a clearance hole is necessary for the center
shaft.
To mount, proceed as follows:
1. Using the drilling template, locate the four panel holes. If the template
is upright the terminals will not be directly on top. When terminals
are required at the top, line marked "T" should be vertical. Drill the
holes.
2. Mount the unit behind the panel as shown using the three ¼"-20
mounting bolts provided. Mount the dial on the front panel, securing
it in place with the 3/8" -32 nut and lockwasher provided. The knob,
when mounted on the shaft covers the nut and lockwasher
MAINTENANCE
When installed and operated in accordance with these instructions, a
POWERSTAT Variable Transformer should require no servicing except
possible replacement of the brush assembly. The brushes should be
inspected periodically and replaced if arcing takes place or if they are
badly worn. Use only the correct Superior Electric replacement brush
assembly. The brushes must be of a special material if proper operation
is to be attained.
REPLACEMENT BRUSH
ASSEMBLIES
REPLACEMENT BRUSH ASSEMBLIES
TYPE
10C
10C-40
12C
Note: 10C and 12C Replacement Brush Assembly are the same.
Whenever unusual mechanical or electrical difficulties are encountered
in the installation or operation of your POWERSTAT Variable Transformer,
consult Superior Electric.
®
Printed in USA
1-800-787-3532
1-800-821-1369
1-800-787-3532, Ext. 70782
1-800-787-3532, Ext. 72058
PART NO. DESCRIPTION
030098-001 RB10C/RB10B
030098-004 RB10C-40/RB10B-40
030098-001 RB12C