Page 2
Intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
Page 3
• Powder coated steel chassis • Optional rack-mounting kits available Congratulations on your purchase of the Peavey UMA™ 35T designed for numerous sound reinforcement applications. The flexible input configurations make this product an excellent choice for paging and/or back/foreground music systems. The UMA 35T job, utilizing an isolated transformer with multiple output configurations.
Page 4
FRONT PANEL FEATURES: CHANNEL 1 LEVEL CONTROL (1) Controls the signal level of the Channel 1 input. CHANNEL 2 LEVEL CONTROL (2) Controls the signal level of the Channel 2 input. CHANNEL 3 LEVEL CONTROL (3) Controls the signal level of the Channel 3 input. LOW EQ CONTROL (BASS) (4) Active equalization control that adjusts the low frequency response.
Page 5
Back Panel: BACK PANEL FEATURES: PAGE INPUT (14) The Page input is a 600 ohm transformer balanced input. The telephone page input should be connected to the + and – terminals; if a shielded cable is used, the shield should be connected to the terminal and not connected at the source.
Page 6
Provides a line level output to drive external power amps, hearing assistance systems, or as a record output for taping. This output is after the EQ and Master Volume Control. LOOP IN/LOOP OUT JACKS (25) Functions as a preamp out/power amp in patch point. The Loop Out signal is a post EQ/Master Volume line level output. LINK SWITCH (26) Breaks the connection between the preamp and the power amp (Loop Out/Loop In).
20 Hz to 20 kHz 1.5 dB into 4 ohms at its direct output at 0.5% or less distortion with hum and noise at least 80 dB below rated output from line level inputs. The unit shall be called the Peavey Architectural Acous-...
Wiring Diagrams Remote Volume 10 K Lin Taper Potentiometer Shielded Cable Figure 1 HIGH Z LOW Z HIGH Z INPUT High Z Input Connections Figure 2 HIGH Z LOW Z LOW Z BALANCED MIC Low Z, Balanced Microphone Input Connections Figure 3...
Page 11
Balanced (1V/600 ) COM XFMR To booster amplifier, etc. 1 V Balanced Output Connectors Figure 4 Balanced (1V/600 ) COM XFMR Jumper Installed 70V "Constant Voltage" Distribution System (Note: Jumper must be in place.) Figure 5...
Page 12
Balanced (1V/600 ) Direct Output to 4 Speaker Figure 6 Figure 7 COM XFMR – Balanced (1V/600 ) – Direct Output to Multiple Speakers in Parallel. Total Impedance = 4 COM XFMR –...
Page 13
For further information on other Peavey Architectural Acoustics products, ask your Authorized Peavey Sound Contractor for the appropriate Peavey Architectural Acoustics catalog/publication. Commercial Sound For Permanent Installations Engineered Sound Products For Permanent Be Sure To Ask About Products In The Following Categories: Modular Series Mixer, Mixer/Amplifiers Rack Kits for MA™...
16. The user should not attempt to service this equipment. All service work should be done by a qualified service technician. 17. This product should be used only with a cart or stand that is recommended by Peavey Electronics. 18. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time.
If within one (1) year from date of purchase a properly installed product proves to be defective and Peavey is notified, Peavey will repair or replace it at no charge. (Note: Batteries and patch cords not covered.) “Original purchaser” means the customer for whom the product is originally installed.