Lamphus SolarBlast SBLS14 Instruction Manual

www.online-led-store.com
US Toll Free: 1-855-LED-ONLINE (533-6654)
International: 1-909-212-0993
Fax: (909) 575-6722
E-mail: support@online-led-store.com
IMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND USE.
• Installer of this product must have a good understanding of automotive electronics, systems,
and procedures.
• In the case that holes must be drilled in order to properly mount the product, the installer must
examine both sides of the mounting surface before drilling begins. It is the installer's
responsibility to be sure that no vehicle components or vital parts could be damaged by the
drilling process. De-burr any holes in order to remove metal shards and remnants. Use
grommets in all wire passage holes.
• If this manual states that this product may be mounted with suction cups, magnets, tape, or
Velcro®, clean the mounting surface and dry thoroughly prior to applying any adhesives for
maximum adhesion.
• Do not attempt to activate or operate this product under hazardous driving situations.
Specifications:
SBLS14 / PSZLEDSTB0701 SBLS24 / PSZLEDSTB0702
Input Voltage: 9 - 30V DC Input Voltage: 9 - 30V DC
Max. Current: 700 mAMPS Max. Current: 900 mAMPS
Max. Output Power: 4W Max. Output Power: 8W
Wiring
WARNING! All customer supplied wires that connect to the positive terminal
of the battery must be sized to supply at least 125% of the maximum operat-
ing current and FUSED at the battery to carry that load. DO NOT USE
CIRCUIT BREAKERS WITH THIS PRODUCT!
RED – To 9 - 30 VDC Power Source
BLACK – To Chassis Ground
WHITE – Group Selection (Note: group selection can only be configured when the units are off.)
-
Units with WHITE connected to the RED will be grouped together as GROUP 1.
-
Units with WHITE NOT connected to the RED will be grouped together as GROUP 2.
-
Units of GROUP 1 and GROUP 2 will flash alternately if its' YELLOW are connected to
each other.
YELLOW – Synchronization and Pattern Selection
-
Connect YELLOW of all units together to enable synchronization.
-
Apply YELLOW to BLACK for a brief second will advance unit to the next flash pattern.
-
Apply YELLOW to BLACK for 3-5 seconds will advance the unit to Steady Mode.
-
Apply YELLOW to BLACK for more than 5 seconds will advance the unit to Off Mode.
BLUE – High/Low Intensity Selection
-
Applying BLUE to RED will engage Low Intensity setting. Disconnecting BLUE from RED
will resume High Intensity setting.
Flash Patterns:
SBLS14 / PSZLEDSTB0701
1. Off Mode 5. Double Flash
2. Double Burst 6. Quad Flash
3. QUad Burst 7. Super Flash
4. Single Flash 8. Single Flash w/ Quad Burst
LAMPHUS
LED Emergency Warning Deck Light Bar
SKU: PSZLEDSTB0701, 702, 704
•
•
SBLS24 / PSZLEDSTB0702
1.
SBLS44 / PSZLEDSTB0704
2.
Input Voltage: 9 - 30V DC
3.
Max. Current: 1.6 AMPS
4.
Max. Output Power: 16W
5.
6.
7.
8.
9.
10.
11.
SBLS44 / PSZLEDSTB0704
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
9. Accelerator
10. Combination Mode
13.
11. Steady Mode
14.
12. Cycle Mode
15.
16.
17.
18.
Online LED Store S2B Inc. ©2015 All Rights Reserved
SolarBlast
®
Deployment area of the vehicle air bags must be cleared. Do not install this product or route
any electrical wires near the air bags deployment areas. Refer to your vehicle owner's manual
for the air bag deployment area. Products or wires mounted in the air bag deployment area will
damage, reduce the effectiveness of the air bag, or even act as a projectile which may cause
serious injury or death. The user/installer of this product assumes full responsibility in
determining the proper mounting location while prioritizing the safety of all passengers in the
vehicle.
This product contains strobe light(s), halogen light(s), high-intensity LEDs, or a combination of
these components. Do not look directly into the lights. Momentary blindness and/or injury to
the eyes could result.
Off Mode 12. Single Flash – All
Single Burst – Split 13. Single Flash –
Single Burst – All Combination
Single Burst – 14. Double Flash – Split
Combination 15. Double Flash – All
Double Burst – Split 16. Double Flash –
Double Burst – All Combination
Double Burst – 17. Quad Flash – Split
Combination 18. Quad Flash – All
Quad Burst – Split 19. Quad Flash –
Quad Burst – All Combination
Quad Burst – Combination 20. Super Flash – Split
Single Flash – Split 21. Super Flash – All
Off Mode 19. Double Flash – Split 2
Single Burst – Split 20. Double Flash – Split 3
Single Burst – All 21. Double Flash – All
Single Burst – 22. Double Flash –
Combination Combination
Double Burst – Split 23. Quad Flash – Split 1
Double Burst – All 24. Quad Flash – Split 2
Double Burst – 25. Quad Flash – Split 3
Combination 26. Quad Flash – All
Quad Burst – Split 1 27. Quad Flash –
Quad Burst – Split 2 Combination
Quad Burst – Split 3 28. Super Flash – Split 1
Quad Burst – All 29. Super Flash – Split 2
Quad Burst – 30. Super Flash – Split 3
Combination 31. Super Flash – All
Single Flash – Split 1 32. Super Flash –
Single Flash – Split 2 Combination
Single Flash – Split 3 33. Single Flash w/ Quad
Single Flash – All Burst – Split
Single Flash – 34. Single Flash w/ Quad
Combination Burst – All
Double Flash – Split 1 35. Accelerator – Split
SBLS14,24,44
™
22. Super Flash – Combination
23. Single Flash w/ Quad Burst
– Split
24. Single Flash w/ Quad Burst
– All
25. Accelerator – Split
26. Accelerator – All
27. Combination Mode
28. Combination Burst
29. California Steady 1
30. California Steady 2
31. Steady Mode
32. Cycle Mode
36. Accelerator – All
37. Combination Mode
38. Combination Burst
39. California Steady 1
40. California Steady 2
41. Steady Mode
42. Cycle Mode
43. Single Flash Scan 75
44. Single Flash Scan Reverse
75
45. Single Flash Scan 120
46. Single Flash Scan Reverse
120
47. Single Flash Scan 375
48. Single Flash Scan Reverse
375