Lamphus PIM-00000038-V002 Quick Start Manual

LED Emergency Warning Traffic Advising Light Bar
Manual ID: PIM-00000038-V002
IMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND USE.
•
Installer of this product must have a good understanding of automotive electronics,
systems, and procedures.
• In the case that holes must be drilled in order to properly mount the product, the
installer must examine both sides of the mounting surface before drilling begins. It is
the installer's responsibility to be sure that no vehicle components or vital parts could
be damaged by the drilling process. De-burr any holes in order to remove metal shards
and remnants. Use grommets in all wire passage holes.
• If this manual states that this product may be mounted with suction cups, magnets,
tape, or Velcro®, clean the mounting surface and dry thoroughly prior to applying any
adhesives for maximum adhesion.
•
Do not attempt to activate or operate this product under hazardous driving situations.
Flash Patterns:
Off Mode
1. 19. Double Flash – Split 2
2. Single Burst – Split 20. Double Flash – Split 3
Single Burst – All
3. 21. Double Flash – All
4. Single Burst – 22. Double Flash –
Combination
Combination
5. Double Burst – Split 23. Quad Flash – Split 1
Double Burst – All
6. 24. Quad Flash – Split 2
7. Double Burst – 25. Quad Flash – Split 3
Combination
26. Quad Flash – All
8. Quad Burst – Split 1 27. Quad Flash –
Quad Burst – Split 2
9. Combination
10. Quad Burst – Split 3 28. Super Flash – Split 1
Quad Burst – All
11. 29. Super Flash – Split 2
12. Quad Burst – 30. Super Flash – Split 3
Combination
31. Super Flash – All
13. Single Flash – Split 1 32. Super Flash –
14. Single Flash – Split 2 Combination
15. Single Flash – Split 3 33. Single Flash w/ Quad
16. Single Flash – All Burst – Split
17. Single Flash – 34. Single Flash w/ Quad
18. Combination Burst – All
Double Flash – Split 1 35. Accelerator – Split
Wiring
WARNING! All customer supplied wires that connect to the positive
terminal of the battery must be sized to supply at least 125% of the
maximum operating current and FUSED at the battery to carry that load.
DO NOT USE CIRCUIT BREAKERS WITH THIS PRODUCT!
RED – To 9 - 30V DC Power Source
BLACK – To Chassis Ground
YELLOW – Synchronization and Pattern Selection
Connect YELLOW of all units together to enable synchronization.
-
Apply YELLOW to BLACK for a brief second will advance unit to the next flash
-
pattern.
Apply YELLOW to BLACK for 3-5 seconds will advance the unit to Steady Mode.
-
Apply YELLOW to BLACK for more than 5 seconds will advance the unit to Off Mode.
-
Specifications:
SBLS64 / PSZLEDSTB0706 SBLS84 /
Input Voltage: 9 - 30V DC PSZLEDSTB0708
Max. Current: 1.125 AMPS Input Voltage: 9 - 30V DC
Max. Output Power: 24W Max. Current: 1.5 AMPS
Max. Output Power: 32W
36. Accelerator – All
37. Combination Mode
38. Combination Burst
39. California Steady 1
40. California Steady 2
41. Steady Mode
42. Cycle Mode
43. Single Flash Scan 75
44. Single Flash Scan
Reverse 75
45. Single Flash Scan 120
46. Single Flash Scan
Reverse 120
47. Single Flash Scan 375
48. Single Flash Scan
Reverse 375
SBLS104 / PSZLEDSTB0710
Input Voltage: 9 - 30V DC
Max. Current: 2.19 AMPS
Max. Output Power: 40W
True Mods © 2012-2021 All Rights Reserved
•
Deployment area of the vehicle air bags must be cleared. Do not install this product or
route any electrical wires near the air bags deployment areas. Refer to your vehicle
owner's anual for the air bag deployment area. Products or wires mounted in the air
bag deployment area will damage, reduce the effectiveness of the air bag, or even act
as a projectile which may cause serious injury or death. The user/installer of this
product assumes full responsibility in determining the proper mounting location while
prioritizing the safety of all passengers in the vehicle.
• This product contains strobe light(s), halogen light(s), high-intensity LEDs, or a
combination of these components. Do not look directly into the lights. Momentary
blindness and/or injury to the eyes could result.
Mounting
CAUTION! Permanent mounting of this product will require drilling. It is
absolutely necessary to make sure that no other vehicle components could
be damaged by this process. Check both sides of the mounting surface
before starting. If damage is likely, select a different mounting location.
Mounting Options:
The SBLS series can be mounted permanently or via suction cups. The mounting brackets
can be secured on to the light bar with a flexible swivel angel of 117 degrees or in a fixed
position with the mounting surface side of the mounting bracket being perpendicular to the
LED lenses of the light bar.
Mounting Options Diagram:
www.truemods.com
US Toll Free: 1-855-533-6654
International: 1-909-212-0993
Fax: (909) 575-6722
E-mail: support@truemods.com