TPG Axim PR-7085P Series Manual

Lock stile (inside)
17.5mm
9.5mm
Drill 4.8mm
(.188) and
countersink
(2)
21.2mm
906.5mm
to floor
INSTALLATION OF
ACTUATOR LINK
Actuator
link
Actuator
Connecting
pin
pin
Place actuator link over actuator
pin & connect using connecting pin
HEADER PREPARATION
Adjustment screw
Trip bracket used as
release when door
stop is not used
THRESHOLD PREPARATION
Drill 3.2mm (.125) holes (2)
MOUNTING INSTRUCTIONS
1. Determine hand of door and prepare inside of lock and hinge
stiles as show.
2. If Cylinder Key Lock is to be used, prepare inside and outside
of lock stile as shown.
3. Insert Rod and Case Assembly into lock stile and secure with
(2) 1/4-20 Shoulder Studs.
4. If Key Lock is used, insert Cylinder in Mounting Pad and
secure with Locking Ring. Install using (2) #8-32x1-23.8mm
Flat Head Machine Screws.
5. Position Exit Pad over stile and attach Actuator Link to Actuator
Pin using Connecting Pin provided. Place on stile over 1/4-20
Shoulder Studs and tighten 3 Socket Head Set Screws to
secure in place.
TITLE
CONCEALED ROD PADDLE HANDLE
PR-7085P SERIES EXIT DEVICE
SUB TITLE
TECHNICAL INFORMATION PR-7085P
Lock stile (outside)
Drill 6.7mm (.266)
holes (2)
17.5mm
For lock cylinder only
Drill 5.2mm (203)
clearance holes (2)
and 35.7mm
cylinder hole
50.8mm
9.5mm
25.4
mm
9.5mm
23.8mm
47.6mm
15.8mm
Dogging
pin
Drill 3.2mm (.125) holes (4)
22.2mm x 27mm hole
for strike or 17.5mm
39.7mm
hole if strike not used
22.2mm
Strike
Strike
22.2mm x 27mm hole
for strike or 17.5mm
hole if strike not used
6. Adjust length of top and bottom Latch Bolts by turning in or
out. When the Panic Arm is fully depressed, the Latch Bolts
should be slightly recessed from flush with the top and bottom
of the door. NOTE: Flat notch side of Bolt must face the
outside of the door. Install top and bottom Latch Bolt Guides
using (6) #10x12.7mm Flat Head Self-threading Screws.
7. Install (2) 1/4-20 Shoulder Studs on hinge stile. Place other
Exit Pad over Studs and tighten 3 Socket Head Set Screws to
secure in place.
8. Prepare header and threshold as shown. If Header and
Threshold Strikes are required, install using (4) #8x9.5mm
Flat Head Self-threading Screws or (4)#8x25.4mm Flat Head
All-purpose screws.
The Parkside Group Ltd
The Willow Centre
17 Willow Lane, Mitcham, Surrey, CR4 4NX
Tel: 020-8685 9685 Fax: 020-8646 5096
Email: axim@parksidegroup.co.uk
Web Site: www.axim.co.uk
8.7mm
9.5mm
16.7mm
Lock
cylinder
9.5mm
191mm
See note #6
11.9mm
Drill 5.2mm (.203)
& countersink (3)
25.4mm
25.4mm
25.4mm
47.6mm
906.5mm
Drill 5.2mm
(.203) and
countersink (3)
14.3mm
See note #6
DOGGING EXIT DEVICE USING DOGGING PIN:
Fully depress push paddle and hold, push up Dogging Pin with
screwdriver and rotate 90 in either direction.
o
TO RELEASE EXIT DEVICE:
Hold push paddle down and rotate Dogging Pin with
screwdriver in either direction until Dogging Pin releases.
DOGGING EXIT DEVICE USING CYLINDER KEY:
Fully depress push paddle and hold, turn Key clockwise
approximately 60 , return Key to centre and remove.
o
TO RELEASE EXIT DEVICE:
Turn key counterclockwise 90 , return Key to centre and remove.
o
SCALE NTS @A4
DATE MARCH 2014
For scaled technical or CAD drawings,
please contact AXIM.
SHEET No.
4:10