Summary of Contents for Belson Outdoors DF6S-P
- Page 1 627 Amersale Drive Naperville, IL 60563 Phone: (800) 323-5664 Fax: (630) 897-0573 sales@belson.com Model # DF6S-P Instructions Sheet RECYCLED PLASTIC HEXAGONAL PLAZA PICNIC TABLE www.belson.com...
- Page 2 BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED. FP - FASTENER PACK ( 1 ) - ONE FASTENER PACK J - TABLE TOP R - TABLE CENTER ( 1 ) - ONE TABLE TOP ( 2 ) - TWO TABLE CENTERS H - TABLE LEG N - LEFT SEAT O - RIGHT SEAT...
- Page 3 BEFORE ASSEMBLY, PLEASE MAKE SURE ALL FASTENERS ARE INCLUDED. 6 - 3/8” X 4-1/4” HEX HEAD BOLT 12 - 3/8” FLAT WASHER 6 - 3/8” NYLON LOCK NUT 6 - #12 X 3” FLAT HEAD PHILLIPS SCREW 48 - #12 X 1-1/2” PAN HEAD PHILLIPS SCREW ALSO NEED FOR THIS ASSEMBLY WILL BE THE FOLLOWING MATERIALS: 1 - #3 PHILLIPS DRIVE BIT 2 - 9/16”...
- Page 4 3/8” X 4 1/4” HEX HEAD BOLT 3/8” FLAT WASHER 3/8” FLAT WASHER 3/8” NYLON LOCK NUT STEP #1: SLIDE ( 1 ) ONE TABLE CENTER ON TO EACH END OF THE TABKE LEG AS SHOWN ABOVE. USE ( 1 ) ONE 3/8”...
- Page 5 3/8” x 4 1/4” HEX HEAD BOLT 3/8” FLAT WASHER 3/8” FLAT WASHER 3/8” NYLON LOCK NUT STEP #2: SLIDE THE REMAINING TABLE LEGS INTO THE TABLE CENTERS. USE ( 1 ) ONE 3/8” X 4 1/4” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER ALONG WITH ( 1 ) ONE 3/8” FLAT WASHER AND ( 1 ) ONE 3/8” NYLON LOCK NUT PER HOLE TO SECURE.
- Page 6 #12 x 2 1/2” PAN HEAD PHILLIPS SCREW STEP #3: WHILE THE TABLE TOP IS UPSIDE DOWN, PLACE THE LEG ASSEMBLY ONTO THE TABLE TOP AS SHOWN ABOVE. ALIGN THE PRE-DRILLED HOLES IN THE TABLE LEGS WITH THE PILOT HOLES IN THE TABLE TOP. USE ( 1 ) ONE #12 X 2 1/2”...
- Page 7 #12 x 3” FLAT HEAD PHILLIPS SCREW STEP #4: WHILE THE TABLE IS UPSIDE DOWN, ALIGN THE PRE-DRILLED HOLES IN THE TABLE LEG TO THE PILOT HOLES IN THE SEAT SUPPORT AS SHOWN ABOVE. USE ( 1 ) ONE #12 X 3” FLAT HEAD SCREW PER HOLE TO SECURE.
- Page 8 #12 X 1 1/2” PAN HEAD PHILLIPS SCREW STEP #5: WHILE THE TABLE IS UPSIDE DOWN, ALIGN THE PRE-DRILLED HOLES IN THE SEAT TO THE PILOT HOLES IN THE SEAT SUPPORT AND THE TABLE LEG AS SHOWN ABOVE. USE ( 1 ) ONE #12 X 1 1/2” PAN HEAD SCREW PER HOLE TO SECURE.
- Page 9 STEP #6: WITH ASSISTANCE TURN THE TABLE OVER ONTO ITS LEGS, PLEASE USE CAUTION FOR THE TABLE WEIGHS APPROXIMATELY 240 POUNDS. www.belson.com...
Need help?
Do you have a question about the DF6S-P and is the answer not in the manual?
Questions and answers