TDS AKKIN 5000 User Manual

www.tdsdive.com
Manual LED light
LIGHT HEADER
INTERRUPTOR
INDICATOR
BATTERY
White Light (4 pcs)
Please read the manual carefully before using the video light
Unpacking
2
1
4
Specifications
- Model no.: AKKIN 5000 Diving Video Light
- Bulb: White CREE SST40 *4 (max 5000 lumens) & Red CREE XP-E N3 *2
(620 nm, 200 lumens)
- Color temperature: 4800 - 5000 K (White only)
- Runtime: White high 70 min, White medium 100 min, Red 120 min
- Output levels: White high >White medium > Red
- Reflector: no hotspot design, no reflector
- Lens: 4 mm toughened glass
- Body material: durable aircraft-grade aluminum
- Angle of light beam: 110°
- Surface treatment: premium type III hard-anodizing
- Color: Black
- Battery: 18650 Li-ion battery pack * 1
- With battery over-discharging protection, polarity reversing protection
- Operation voltage: 4.2 V to 2.8 V
- Waterproof: up to 100 Meters
- Dimensions: 125 mm (length) * 52 mm (dia. of light head) * 47 mm
(dia. of light body)
- Weight in air: approx. 230 g. (without battery pack); approx. 387 g.
(with battery pack)
- Underwater weight: approx. 194 g. (with battery pack)
Modes changing
When the light is off, long press the switch for three seconds to turn on the
light. When the light is on, Successively click the switch to cycle through
White high, White medium, Red, and off. At White light mode, the light can
also be switched off by long pressing the switch for three seconds.
Power indication
Power indicator surrounding the switch lights up in green, or yellow,
or red, when power capacity is above 70%, or between 70-40%, or
between 40-10%. It flashes in red for power capacity between
10-5%, and switches off automatically when the power capacity is
below 5% to prevent over-discharging battery.
TAIL CAP
BATTERY
Red Light (2 pcs)
3
1
2
3
4
5
5
USER MANUAL
1. Please never attempt to repair or modify the light yourself.
2. Please handle illuminants with care to avoid breakage. While being hit on,
illuminants can break or splinter. Splinters can cause eye and skin injuries.
3. Please check the light regularly for sharp edges, scratches or damages to the
surface or O-ring, as this can cause the light to flood under pressure. PLEASE
LUBRICATE THE O-RING, AND REPLACE IT TIMELY. (Please avoid applying lubricant
to circuit board, which may affect the conduction.)
4. Please rinse the product surface thoroughly after each use, and allow sufficient
time for it to dry both inside and outside before storage.
5. Please remove the battery pack from compartment for transport or storage.
Do not lay the battery pack in a fire or expose it to direct heat. Do not wet or hit
the battery pack. Please charge it after each use, or once every three months, to
avoid over-discharging.
6. Please never leave the light unattended when it is on.
7. Please keep the device out of the reach of children or pets.
8. Please never shine the light to human or pet's eye.
9. Please do not use other battery pack for this light.
10. To prevent light's inner parts damaged by over-heating, please do not cover
or block the light head when the light is switched on in the air.
11. In case of accidental flooding, please remove the battery pack, and dry the
light and battery compartment as soon as possible, to prevent the secondary
damage.
Video light
Li-ion battery
Charger
3 year manufacturer defect warranty , this warranty does not cover failures or
O Ring
defects resulting from misuse of the equipment (e.g. modifications or damage),
YS Adapter
natural disasters, problems with the charger or battery, including improper
installation of the battery.
The light flashes 3 times if the power capacity reaches 10-5%; it repeats
after 5 seconds. (Then the light switches to lower brightness. if it is originally
at the white light mode.) The light switches off automatically when the
power capacity is less than 5% to prevent over-discharging battery.
1. Holding the light body, with light head pointing upward; unscrew the light head.
2. Remove used battery pack from compartment, if there is any; and put in fully
charged battery pack per polarity signs.
3. Screw light head down. Do not overtighten to break the O-ring.
1. Please keep the charger and the battery pack away from the flammable
or explosive material. Plug the charger in the power socket, when its other
side is not connected with the battery pack, its indicator lights in green in
the free-load status.
2. Plug the other end of charger in the port of the battery pack. The
charger's indicator light is red if the charging is in process; and it turns green
after the charging is completed.
3. Charge the battery under supervision and disconnect the charger when
charging is complete.
www.tdsdive.com
Caution
Warranty return policy
Low battery warning
Battery insalation
Battery charging
Battery
DC charger plug
U P D A T E I N S T R U C T I O N S
Tail Cap