Summary of Contents for SITRONICS INTRACOM omniBAS
- Page 1 Next Generation Ethernet Microwave Backhaul Solution Installation and Cabling Manual Edition 6.0 Confidential...
- Page 2 The information contained in this document is subject to change without prior notice. ã INTRACOM S.A. TELECOM SOLUTIONS, 2014. All rights reserved. All copyright, intellectual and industrial rights in this document and in the technical knowledge it contains are owned by INTRACOM S.A. TELECOM SOLUTIONS and/or their respective owners. This document is made available to the end users only for their internal use.
- Page 3 Document Revision History OmniBAS -2W/4W/8W Installation and Cabling Manual - Edition 6.0 Document Revision History Revisions This page shows the main changes effected in relation to the previous edition of the OmniBAS IDU Installation: Revisions Previous: 4.0 – 5.1 Current: Reasons of The table below shows the reasons for the document change effected in change...
- Page 4 OmniBAS -2W/4W/8W Document Revision History Installation and Cabling Manual - Edition 6.0 (Page intentionally left blank)
- Page 5 OmniBAS -2W/4W/8W Installation and Cabling Manual - Edition 6.0 Table of Contents Introduction ........................1 About this Document......................1 Overview of OmniBAS Product Family ................2 Safety Precautions ......................5 Installation Tools......................6 Installation Material......................7 OmniBAS-2W........................7 OmniBAS-4W/8W ......................10 OmniBAS-4P........................14 Before Starting the Installation..................16 Installation Prerequisites ....................16 Cabling Overview ......................20 Modem Cabling ........................21 RJ-45 Cabling (Ethernet Payload) ...................23...
- Page 6 Table of Contents BNC Terminations (Unbalanced 75 Ω) ................62 RJ-45 Terminations (Balanced 120 Ω)................65 I/O Cables ........................68 Ethernet Cables .......................70 Cable Characteristics ....................71 GbE Cable Characteristics....................71 OmniBAS-2W........................71 OmniBAS-4W/8W ......................72 OmniBAS-4P........................73 Fast Ethernet Cable Characteristics ................74 OmniBAS-2W........................74 OmniBAS-4W/8W ......................74 OmniBAS-4P........................75 STM-1 Cable Characteristics ...................76 OmniBAS-4W/8W ......................76 Appendix-A: Modem Card Installation / Removal ..............77 Appendix-B: I/O Connections ....................80...
- Page 7 Equipment Disposal Disposal of old electrical and electronic equipment (applicable through the European Union and other European countries with separate waste collection systems). This symbol, found on this product and any of its parts or on its operating instructions or on its packaging, indicates that electrical and electronic equipment may not be disposed of as unsorted municipal waste.
- Page 8 Declaration of Conformity Hereby, Intracom S.A. Telecom Solutions declares that the product OmniBAS is in compliance with the essential requirements and other relevant provisions of the directive 1999/5/EC, and with the requirements of the RoHS directive 2011/65/EU. For further information, please visit the following URL: http://emc.intracom-telecom.com/ Δήλωση...
- Page 9 OmniBAS -2W/4W/8W Installation and Cabling Manual - Edition 6.0 Introduction About this Document Scope of This document provides information concerning the installation and cabling document of the following OmniBAS™ Indoor Units (IDUs) units: • OmniBAS • OmniBAS • OmniBAS • OmniBAS Target This document is addressed to certified technicians with wireless equipment Audience...
- Page 10 Chapter 1. Introduction Overview of OmniBAS Product Family Introduction The OmniBAS™ family of Intracom Telecom IP MW PtP portfolio comprises: • Split-mount systems: − OmniBAS™ Indoor Units (IDUs) 1RU / 2RU high and 19″ wide. − OmniBAS™ Outdoor Units (ODUs) & antenna systems. •...
- Page 11 OmniBAS -2W/4W/8W Installation and Cabling Manual - Edition 6.0 Overview of OmniBAS Product Family, Continued OmniBAS™ The OmniBAS™ Indoor Units (IDUs) are shown below: IDUs Indoor Unit (IDU) Description It is a Native-IP, 1RU unit accommodating up to two modems. It can be positioned at the edge of the network, or can be used as a repeater and even as a ring node.
- Page 12 Chapter 1. Introduction Overview of OmniBAS Product Family, Continued OmniBAS™ Indoor Unit (IDU) Description IDUs, continued OmniBAS™-8W is the base for the leading CBAN (Converged Backhaul Aggregation Node) supporting flexibly all MW technologies appropriate for HetNets backhauling. It is a Native-IP, highly-modular 2RU indoor unit and is capable of accommodating in the same chassis the following cards:...
- Page 13 OmniBAS -2W/4W/8W Installation and Cabling Manual - Edition 6.0 Safety Precautions PROPER GROUNDING Never power up the indoor equipment not yet connected to a proper grounding system. There is risk of equipment failure and/or electrical shock. Ensure that the indoor grounding system measures a path resistance less than 4 Ω.
- Page 14 Chapter 2. Installation Tools Installation Tools Tools List This chapter describes the tools requirements for the proper equipment installation Item Photo Description Cros screw drivers: • (A): PH-1 • (B): PH-3 Blade Wire Stripper Cable Jacket Stripper Crimping tool for 1,5 / 2,5 &...
- Page 15 OmniBAS -2W/4W/8W Installation and Cabling Manual - Edition 6.0 Installation Material OmniBAS-2W Package The following table depicts the IDU contents for installation: Contents Description IDU Factory Test Results Paper. IDU Standard Installation Material. OmniBAS -IDU. The package contents is the same for all types of OmniBAS -2W IDU’s.
- Page 16 Chapter 3. Installation Material OmniBAS-2W, Continued Mounting kit Description (per indoor unit) Screw, M6 x 12 Washer, od = 15, id = 6,4 Caged nut, M6 IF Tail The following set is supplied per modem card. Description (per indoor unit) IF Tail 1,5m, RG223 SMA-type male, R/A to N-type female connector (A): O-ring...
- Page 17 OmniBAS -2W/4W/8W Installation and Cabling Manual - Edition 6.0 OmniBAS-2W, Continued Power connector Description (per indoor unit) 2-pole power connector Heat Shrinkable Tube, 10 cm Metallic pins for power connector for cable up to 1.5 Metallic pins for power connector for cable up to 2.5 Tie-wraps Description (per indoor unit)
- Page 18 Chapter 3. Installation Material OmniBAS-4W/8W Package The following table depicts the IDU contents for installation: Contents OmniBAS-4W OmniBAS-8W Description IDU Factory Test Results Paper. IDU Standard Installation Material. OmniBAS -IDU. Keep the packaging of the equipment in good condition for later use (i.e.
- Page 19 OmniBAS -2W/4W/8W Installation and Cabling Manual - Edition 6.0 OmniBAS-4W/8W, Continued Mounting kit Description (per indoor unit) Screw, M6 x 12 Washer, od = 15, id = 6,4 Caged nut, M6 IF Tail The following set is supplied per modem card. Description (per indoor unit) IF Tail 1,5m, RG223 SMA-type male, R/A to N-type...
- Page 20 Chapter 3. Installation Material OmniBAS-4W/8W, Continued Power connector Description (per indoor unit) 2-pole power connector Heat Shrinkable Tube, 10 cm Metallic pins for power connector for cable up to 4.0 Tie-wraps Description (per indoor unit) Tie-wraps 45cm, for indoor cables fastening The screw and nut included are for connection of OmniBAS IDU grounding cable to the rack...
Need help?
Do you have a question about the INTRACOM omniBAS and is the answer not in the manual?
Questions and answers