Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Goodwe BCL9600
Summary of Contents for Goodwe BCL9600
- Page 1 User Manual Battery Enclosure BCL9600 V1.2-2022-10-30...
-
Page 2: Table Of Contents
User Manual V1.2-2022-10-30 Content TABLE OF CONTENTS 01 Product Introduction ..........1 1.1 Dimensions....................1 1.2 Parts List ....................1 02 Installation .............. 2 2.1 Tools required ...................2 2.2 Location and environmental requirement ..........2 2.3 Preparations ....................3 2.4 Mounting the Enclosure ................4 2.5 Inserting the Batteries ................4 BMS Connections ............ - Page 3 Copyright Statement User Manual V1.2-2022-10-30 Trademarks and other GOODWE trademarks are trademarks of GoodWe Technologies Co.,Ltd. All other trademarks or registered trademarks mentioned in this manual are owned by GoodWe Technologies Co.,Ltd. NOTICE The information in this user manual is subject to change due to product updates or other reasons.
-
Page 4: Product Introduction
User Manual V1.1-2022-06-30 01 Introduction 01 Product Introduction 1.1 Dimensions The Battery Enclosure dimensions are: width 516mm, depth 280mm, height 1155mm (without the feet installed) and width 516mm, depth 280mm, height 1205mm (with the feet installed). 516mm 280mm Figure 1: Dimensions 1.2 Parts List Expansion Short grounding... -
Page 5: Installation
02 Installation User Manual V1.2-2022-10-30 The following lists are only for battery enclosure parallel connection. Network cable Silicon stopper Right panel x 1 Screw plug x 1 Top panel x1 Long grounding Countersunk Wiring slot x 1 Left panel x 1 wire x 1 screw x N 02 Installation... -
Page 6: Preparations
2. Screw the two feet to the base of the battery enclosure, using the three screws provided. 3. Once the feet are fixed, the battery enclosure is ready for installation as shown in Figure 4. Figure 4: Battery Enclosure with the feet Figure 2: BCL9600 out of the packing box. attached and ready for installation. Feet Inside bottom view of Enclosure without feet Figure 3: Battery Enclosure feet and mounting screws. -
Page 7: Mounting The Enclosure
2.5 Inserting the Batteries Note: The battery switch should remain off during the installation process. The enclosure can be used to house Li-ion battery types, the following installation uses GoodWe SECU-A battery as an example. Up to two GoodWe SECU-A(4.8kWh) battery packs with a total storage capacity of 9.6 kWh. - Page 8 Figure 8: Inside view of BCL9600 with inserted two Goodwe SECU-A batteries. 3. If you are using GoodWe SECU-A battery packs, connect the bonding leads between each battery and the earthing studs inside the enclosure. Side of battery enclosure Front view of battery enclosure...
- Page 9 02 Installation User Manual V1.2-2022-10-30 Figure 10: BCL9600 with batteries and connected (Goodwe SECU-A). At this stage the preliminary installation of the Battery Enclosure is complete. The next step is the connection of the BMS cables.
-
Page 10: Bms Connections
BMS Connections The BMS (Battery Management System) communication for GoodWe SECU A5.4-20 or SECU A5.4L battery is as follows: 3.1 DIP Switch Calibration (Only for SECU-A5.4L) The DIP switches shall be configured differently between single piece battery and multi battery paralleling system. -
Page 11: App Setting (On Solargo)
Description From Cable label Master battery COM 1 BMS feed through port To inverter port to inverter port GoodWe SECU-A Fan Controller To Battery port Battery 2 +/-port Cabinet of battery (Figure 12) Link Port COM 2 of the master... - Page 12 400Vac 2-pole circuit breaker 400Vac 2-pole Earth circuit breaker WiFi circuit breaker Grid main 230V switch board utility grid Manual AC load connection 25 amp 250Vac terminals bypass switch 491.9965 BMS to GoodWe SECU-A 'CAN' Port Figure 11: GoodWe SECU-A...
-
Page 13: Connecting The Battery Enclosure To The Inverter
04 Connecting the Battery Enclosure to the Inverter User Manual V1.2-2022-10-30 04 Connecting the Battery Enclosure to the Inverter CAUTION! The inverter should be powered down during this process. The battery enclosure is now ready to be connected to the inverter mounted on the same wall above the battery enclosure as per figure 13. - Page 14 User Manual V1.2-2022-10-30 04 Connecting the Battery Enclosure to the Inverter Figure 12: BCL9600 Battery Enclosure connected to inverter (GoodWe Secu-A)
-
Page 15: Commissioning The Battery
SolarGo app. Note: You need to check the inverter’s commissioning steps to complete the commissioning of the whole system. Figure 13: The completed installation of BCL9600... - Page 16 Website GoodWe Technologies Co., Ltd. No. 90 Zijin Rd., New District, Suzhou, 215011, China www.goodwe.com service@goodwe.com 340-00884-00 Local Contacts...
Need help?
Do you have a question about the BCL9600 and is the answer not in the manual?
Questions and answers