Download Print this page

Conner CFP1080S Product Manual

Intelligent disk drive

Hide thumbs

Table Of Contents

Table of Contents

Table of Contents
Drive Overview
Drive Description
Drive Features
Drive Components
Mechanical Design Features
Drive Assembly Housing
Drive Motor and Spindle
Head Positioning Mechanism
Read/Write Heads and Disks
Data and Power Connections
Electrical Design Features
Integrated Circuit
Circuit Board
Read/Write Channel
Firmware
Specifications
Specifications in this Chapter
Drive Capacity
Formatted Capacity
Physical Configuration
Physical Configuration Per Zone
Performance Characteristics
Seek Times (Typical)
Average Latency
Rotation Speed (+0.1%)
Controller Overhead
Start Time(Power Up)
Stop Time at Power down
Interleave
Read/Write Characteristics
Recording Method
Recording Density (Maximum)
Flux Density (Maximum)
SCSI Characteristics
Command Set
Data Transfer Rate
Maximum Synchronous Transfer Offset
Maximum Tagged Command Queue Depth
Reliability
Data Reliability
Component Design Life
Start/Stop Cycles
Mean Time between Failures
Mean Time to Repair
Preventive Maintenance
Power Requirements
Minimum/Maximum Voltage
Environmental Tolerances
Magnetic Field
Acoustic Noise
Safety Standards
Physical Characteristics - CFP1080E
Physical Characteristics - CFP1080S
Drive Operation
Drive Functions
Drive Operational Modes
Error Correction
Read Retry Operations
Downloadable Microcode
Buffer Management and Command Execution
SCSI Look Ahead Control Code
Write Caching
SCSI Queuing Control Code
Command Re-Ordering
Buffer Management
Installing the Drive
Take These Precautions
Installing a CFP1080E
Setting the Drive's Jumpers - CFP1080E
Setting the SCSI Bus Address - CFP1080E
Disabling Spin-Up at Power on - CFP1080E
Delaying Spin up at Power on - CFP1080E
Host Interface Connection - CFP1080E
Attaching Power to the Drive - CFP1080E
Mounting the Drive - CFP1080E
Installing a CFP1080S
Setting the Drive's Jumpers - CFP1080S
Setting the SCSI Bus Address - CFP1080S
Disabling Spin-Up at Power on - CFP1080S
Disabling SCSI Bus Terminator Power (TERMPWR) - CFP1080S
Setting the Bus Termination - CFP1080S
Cabling the Drive - CFP1080S
SCSI Bus Cable
Spindle Synchronization
Attaching Power to the Drive - CFP1080S
Attaching a Remote LED - CFP1080S
Mounting the Drive - CFP1080S
Interface Physical Characteristics
Electrical Description
Output Characteristics
Input Characteristics
Model-Specific SCSI Physical Characteristics
CFP1080E (WIDE, 80-Pin Single Connector Attachment [SCA])
External Terminator Power
Internal Termination
Cable Requirements
Connector Requirements
Single Connector Attachment (SCA) Signal Definitions
Power
Spindle Sync
LED out
Motor Start Controls
SCSI ID Selection
Interface Pin Assignments
Model CFP1080S (Narrow, 50-Pin SCSI)
External Terminator Power
Internal Termination
Cable Requirements
Connector Requirements
Interface Pin Assignments
Interface Timing Requirements
SCSI Command Implementation
SCSI Command Summary
Drive Dependent SCSI Mode Sense Data
Format Device Page - 03 H
Rigid Disk Geometry Page - 04 H
Notch Page - 0C H

Quick Links

Download this manual

CFP1080S/CFP1080E

Intelligent Disk Drive

Product Manual

Production Release Per ECO 6561

P/N 20401007-001

Revision A

August 1995

3081 Zanker Road

San Jose, CA 95134-2128

(408) 456-4500

Table of Contents

Conner CFP1080S Product Manual

Quick Links

Need help?

Questions and answers

This manual is also suitable for:

Conner CFP1080S Product Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Conner CFP1080S

This manual is also suitable for:

Table of Contents