Advertisement
Quick Links
R•O•M M4000 Power - Series IV Shutter Door
Congratulations on your purchase of the R•O•M M4000 Power Operated Series IV Roll-up Shutter Door!
Please read and carefully follow these instructions!
You will need the following parts and tools for installing your Power Operator and Power Lock System;
please note that these are not included with your system.
•
Fasteners for drip rail and track (Self-tapping hex-head #10 machine or sheet metal screws are
recommended)
•
Drill
•
Drill bits-#29, 11/64", 3/16", 3/8, and 1/2
•
Single Pole Double Throw Momentary Switches for Door/Lock Input Switches (On)-Off-(On)
•
Door Ajar/Compartment White Light
•
10 Amp and 20 Amp Fuse and holder
•
Clear indoor/outdoor silicone sealant
•
Screwdriver – Phillips
•
Wire cutters
•
Wire crimp
•
Tape measure
•
Marking pen
•
Pop rivet gun for 3/16" pop rivets
•
Rubber headed mallet
•
Paper towels
•
Rubbing alcohol
•
7/16" wrenches and / or sockets
•
DC current meter (suggested)
•
Wire nuts and/or solder less connector for joining 22 gauge wires to vehicle wiring
Note: Size vehicle wiring to allow 10 amps for each power operator system, if two are running
concurrently allow 20 amps, etc...
Installation Instructions
Page 1 of 17
Street • Belton, MO • 800-827-3692
rd
6800 East 163
Copyright © 2022. All Rights Reserved.
FM-8.5-384 / D / 06-24-2022
Advertisement
Summary of Contents for Safe Fleet R O M IV Series
- Page 1 R•O•M M4000 Power - Series IV Shutter Door Installation Instructions Congratulations on your purchase of the R•O•M M4000 Power Operated Series IV Roll-up Shutter Door! Please read and carefully follow these instructions! You will need the following parts and tools for installing your Power Operator and Power Lock System; please note that these are not included with your system.
- Page 2 R•O•M M4000 Power - Series IV Shutter Door Installation Instructions Overview For a successful installation of the R•O•M Roll-up Shutter Door, follow these steps 1) Unpacking 9) Installing the Proximity Switch 2) Pre-Drilling Holes 10) Attaching the Track 3) Attaching the Sill Plate 11) LED DuroStrip Compartment Lighting 4) Attaching the Pennant Plates...
- Page 3 R•O•M M4000 Power - Series IV Shutter Door Installation Instructions Note: If the sill plate option is included, place the track on the sill plate or 1/8 up from the bottom of the compartment prior to drilling. d) If pre-drilled track was ordered. Match drill 11/64 holes in the vehicle body where holes are present in the track.
- Page 4 R•O•M M4000 Power - Series IV Shutter Door Installation Instructions Installing the Power Door Control Module (Reference wiring diagram on page 9) a) Connect the wires as shown in the diagram. Use the appropriate fuses as noted. b) Install the power door control module to the left side near the pennant plate. 7.
- Page 5 R•O•M M4000 Power - Series IV Shutter Door Installation Instructions 8. Installing the Power Lock a) Mount the power lock to the track if not factory installed. The track will be pre-drilled and slotted for the power lock. Mount the lock using 3/16” pop rivets as shown in Fig.
- Page 6 R•O•M M4000 Power - Series IV Shutter Door Installation Instructions c) To create a watertight opening, use a silicone sealant to seal between the track, sill plate (optional), and compartment. Silicone sealant can also be applied around the bottom of the track if it does not seat properly with the bottom of the compartment opening.
- Page 7 R•O•M M4000 Power - Series IV Shutter Door Installation Instructions Fig. 12 13. Installing the Drip Pan and Drain Hose (Optional) a) Refer to FM-8.5-191 for the installation of the drip pan and drain hose. 14. Installing the Pull Rope or Pull Strap (Optional) a) Refer to FM-8.5-227 for the Pull Rope Installation or FM-8.5-49 for the Pull Strap Installation.
- Page 8 If you have any questions, please contact your R•O•M Customer Service Representative at 800-827-3692. These drawings and the information contained herein are the confidential and proprietary intellectual property of Safe Fleet and should not be disclosed to any third party without the express prior written consent Safe Fleet.
- Page 9 R•O•M M4000 Power - Series IV Shutter Door Installation Instructions Street • Belton, MO • 800-827-3692 6800 East 163 Copyright © 2022. All Rights Reserved. Page 9 of 17 FM-8.5-384 / D / 06-24-2022...
- Page 10 R•O•M M4000 Power - Series IV Shutter Door Installation Instructions Street • Belton, MO • 800-827-3692 6800 East 163 Copyright © 2022. All Rights Reserved. Page 10 of 17 FM-8.5-384 / D / 06-24-2022...
- Page 11 R•O•M M4000 Power - Series IV Shutter Door Installation Instructions R•O•M Roll-up Door Series IV – M4000 Power Operated System Assembly Drawing R04317 Street • Belton, MO • 800-827-3692 6800 East 163 Copyright © 2022. All Rights Reserved. Page 11 of 17 FM-8.5-384 / D / 06-24-2022...
- Page 12 R•O•M M4000 Power - Series IV Shutter Door Installation Instructions R•O•M Roll-up Door Series IV – M4000 Power Operated System Assembly Drawing R04317 Street • Belton, MO • 800-827-3692 6800 East 163 Copyright © 2022. All Rights Reserved. Page 12 of 17 FM-8.5-384 / D / 06-24-2022...
-
Page 13: Cleaning And Maintenance
R•O•M M4000 Power - Series IV Shutter Door Installation Instructions APPENDIX CLEANING, MAINTENANCE, AND TENSION ADJUSTMENT INSTRUCTIONS THE R•O•M ROLL-UP SHUTTER DOOR IS MADE OF ANODIZED ALUMINUM Anodized aluminum is extremely hard and resistant to abrasion. Anodized aluminum can retain its original appearance indefinitely if you follow a sound cleaning and maintenance program. -
Page 14: Tension Adjustment
R•O•M M4000 Power - Series IV Shutter Door Installation Instructions CLEANING THE FRICTION AREAS In the operation of the shutter there are friction areas that will need to be cleaned. After cleaning these points they need sprayed with dry silicone to increase the ease of operation. Never use lithium or grease. - Page 15 R•O•M M4000 Power - Series IV Shutter Door Installation Instructions A. Adjusting the tension if the compartment is easily accessible 1. Open the shutter completely. 2. Pull down on the bottom of the roll inside the compartment (Ref. Fig. 1) overcoming spring tension.
- Page 16 R•O•M M4000 Power - Series IV Shutter Door Installation Instructions 6. Replace the tension pin and re-attach the straps to the top slats. 7. Remove the tension pin and slowly let the tension onto the shutter. Route the curtain over the nylon rollers and raise the curtain up to the header.
- Page 17 If you have any questions or problems, please contact your Customer Development Representative at 800-827-3692. These drawings & the information contained herein are the confidential & proprietary intellectual property of Safe Fleet and should not be disclosed to any third party without the express prior written consent Safe Fleet.