Summary of Contents for Kowa KE 0202CT2
- Page 1 TWISTED PAIR TRANSMITTER KE 0202CT2 (w-type) Instruction Manual Thank you for your purchase of this product Please be sure to read this manual completely prior to usage of product Ver 2.5E...
-
Page 2: For Canada
RGB Interface Cable Use of a RGB interface cable longer than 3 m (9.84 feet) is not recommended. For U.S.A NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 3 U s a g e C a u t i o n s Please be sure to read this manual prior to usage of product. After reading,keep it in a place near the equipment where it can be easily referred to. ・If this symbol is ignored death or serious injury may W a r n i n g occur.
- Page 4 Warning ◆Do not continue to use this product if any of the following occurs ※It may cause fire or electric shock ・If you smell a strange odor or smoke. ・If water or a foreign object gets inside the product. ・After dropping the product. ・If the power cord is damaged.
- Page 5 C a u t i o n ◆Do not put this product in the following places. ※May cause fire or electric shock. ・Places where there is a lot of humidity or dust. ・Places where there is steam. ...
- Page 6 Index 1. About this product 1-1. Product and accessories 1-2. General information 2. Connection 2-1. The cautions and warnings 2-2. Preparation of cable 2-3. Cable mounting kit (Twisted pair transmitter) 2-4. How to connect 3. Denomination and function of each parts 3-1.
- Page 7 1. About this product (KE 0202CT2(w-type)) 1‑1. Product and accessories Please check that you have the accessories and items shown. KE 0202CT2 VIDEO POWER M.SW INPUT SELECT TWISTED PAIR TRANSMITTER Main unit of KE 0202CT2(w-type) AC adapter Angle mounting kit×2 Cable mounting kit...
- Page 8 1‑2.General information The products, KE 0202CT2W (w-type)/KE 0101CR-BW, are a transmitter and receiver for long distance transmission of a wide band signal such as a computer, high definition TV or a composite signal through a twisted pair cable (CAT5 e or CAT6). They also have the function of long distance transmission of stereo sound and RS232C serial data.
- Page 9 Kowa is not responsible for any damage or injury caused as a result of improper use. ・Turn off the transmitter, receiver, and any product that is connected to the devices when removing or installing twisted pair cables.
- Page 10 2‑2.Preparation of a cable A CAT5e or CAT6 cable is used to connect the twisted pair transmitter and receiver. The transmitter and receiver are connected straight through as shown in the diagram below. ※ Please keep the combination of the pair lines as follows. If the combination of a pair line is incorrectly installed , there is a possibility that the quality of the image may deteriorate.
- Page 11 2‑3. Cable mounting kit (Twisted pair transmitter) A mounting kit for the twisted-pair cable is enclosed with the twisted pair transmitter. Use the following diagram to attach the mounting kit. Diagram for attachment Cable mounting kit Cable mounting kit Cable mounting kit KE 0202CT2 VIDEO POWER...
- Page 12 Ⅱ．Refer to the following diagrams when connecting cables to the twisted pair transmitter. ⑨ ⑩ ④ ⑦ ⑧ RS-232C AUDIO IN AUDIO OUT Y/VIDEO DC12V IN Y/VIDEO RGB IN RGB OUT OUT 1 OUT 2 ⑥ ① ② ③ ⑤ a)．Composite signal Connector ④...
- Page 13 c).RGB signal Connector ① Connector ② RGB IN RGB OUT RGB Input RGB Output(for monitering) d).Audio signal Connector ⑩ Connector ⑨ AUDIO IN AUDIO OUT Input L Input R Output L Output R (for monitering) Ⅲ.Refer to the following diagrams when connecting cables to the twisted pair receiver. ① ② a).Composite signal Connect the "VIDEO OUT "of the twisted pair receiver to the "VIDEO IN"...
- Page 14 b). Audio Signal Connect the "AUDIO OUT" ( Stereo mini jack) of the twisted pair receiver to the "Audio In" of the PDP. Back panel of PDP Connector ② AUDIO OUT AUDIO Ⅳ.Connect the twisted pair transmitter and receiver with the correct twisted pairs using CAT5e or CAT6 cable.
- Page 15 3.Denomination and function of each parts 3‑1．Function of the twisted pair transmitter 3‑1‑1．Front panel of the twisted pair transmitter KE 0202CT2 VIDEO POWER M.SW INPUT SELECT TWISTED PAIR EXTEND TRANSMITTER ① ② ③ ① POWER After connecting the adapter cable the power will turn on and the power indicator lamp will light up.
- Page 16 3‑1‑2.Back panel of the twisted pair transmitter ⑨ ⑩ ④ ⑦ ⑧ RS-232C AUDIO IN AUDIO OUT Y/VIDEO DC12V IN Y/VIDEO RGB IN RGB OUT OUT 1 OUT 2 ⑥ ① ② ③ ⑤ ① RGB IN High density D-SUB 15pin : Connector for image input This is the input connector for RGB signal (Not available for GonSYNC) ※ Please use a cable under 3m (9.84feet) in length when connecting.
- Page 17 ⑥ DC12V IN It could be plugged an 12V dedicated voltage adapter. ⑦ FG Frame ground Connect a ground wire to the transmitter. ⑧ RS‑232C Serial communication for RS232C (transmission only). D-SUB 9pin (male) is necessary. Uses a RS-232C Straight cable. (Please refer to the appendix for details) ⑨ AUDIO IN RCA pin jack: connector for audio input The input connector for audio.
- Page 18 4.Operation 4‑1．Operation of the twisted pair transmitter 4‑1‑1．Setting a dip switch on the base Two dip switches are installed on the base that allow terminal No. 4 and 11 of the transmitter. RGB IN/OUT connector to be set to loop through or ground. Please refer to the diagram below for settings.
- Page 19 b).Transmitting a component signal Transmitter settings: Set the INPUT SELECT to VIDEO and M.SW No.8 to "ON". VIDEO M.SW PDP settings: Select "INPUT 1"and on the PDP screen menu, select "component" from the "component/RGB" options (Please refer to the instruction manual of the PDP). c).Transmitting an RGB signal Transmitter settings : Set the INPUT SELECT switch to RGB.
- Page 20 4‑1‑3.Mode switch settings The M.SW switches can be set as follows. Dip switch No. A detail of setting Reserved 〃 〃 〃 〃 〃 〃 Switching between composite (OFF) and component (ON) signals. ※ INPUT SELECT switch is only effective when set to VIDEO ※ All M.SW switches are set in the "Off"...
-
Page 21: Installing The Transmitter
5.Installing the transmitter The transmitter can easily be placed on a desk, etc. utilizing the attached rubber feet. For mounting, two angled mounting kits have been included. ※ Remove the rubber feet from the main body if mounting with the angle mounting kits. a) Installing on a flat surface Installation on a ceiling, wall, under a desk can be done with the angled mounting kits. ... - Page 22 b) Attaching to a rack 1U x 1 rack mount set 1U x 2 rack mount set Using the above mount kits allow the transmitter to be attached to a rack. The mount kits are the same color as the casing of the transmitter giving the outside an aesthetically pleasing look. The rack mounts are optional accessories.
-
Page 23: Specification
6．Specification Model name KE 0202CT2(w-type) Number of input Image (RGB, VIDEO) each 1 system, Audio 1 system or RS-232C 1 system channels Number of output Output for monitor (RGB, VIDEO, Audio) each 1 system, Output for channels extension 1 system (2 distribution) -
Page 24: Troubleshooting
7．Trouble Shooting Reference Problem Please check the following The image can't be seen ● Is the power of PDP turned on ? Please refer to a on the PDP instruction manual of PDP ● Is the lamp of the twisted pair transmitter lit-up? −... - Page 25 The image of composite ● Is the lamp of the twisted pair transmitter lit? Is the AC − or component signals adapter cable properly connected to AC90-264V line and can not be seen in a twisted pair transmitter? MONITOR OUT of the ●...
- Page 26 Appendix Ⅰ．Wiring diagram for RS232C Connection between a computer and the transmitter The RS232C straight cable of D-SUB 9pin can be used. (Both ends are female connectors) Computer (D-SUB 9pin) Transmitter (D-SUB 9pin) Pin No. Name of signals Pin No. Name of signals DCD(Data carrier detect) RXD（Recived data） TXD（Transmitted data）※No data sending TXD（Transmitted data）...
- Page 27 ※ Design and specifications are subject to change without notice. 2005.09.22...
Need help?
Do you have a question about the KE 0202CT2 and is the answer not in the manual?
Questions and answers