Related Manuals for Cherry Aerospace CHERRYLOCK G695B
Summary of Contents for Cherry Aerospace CHERRYLOCK G695B
- Page 1 TM-G695B Rev.: D DCR# 16-0786 DATE: 10/13/16 Federal Identification Code: 11815 © 2016 Cherry Aerospace Original Instructions G695B RIGHT ANGLE, DOUBLE ACTION ® CHERRYLOCK POWER TOOL...
-
Page 2: Table Of Contents
DATE: 10/13/16 Federal Identification Code: 11815 © 2016 Cherry Aerospace T H E G 6 9 5 B D O U B L E A C T I O N R I G H T A N G L E R I V E T E R TABLE OF CONTENTS Description ...................................... -
Page 3: Description
TM-G695B Rev.: D DCR# 16-0786 DATE: 10/13/16 Federal Identification Code: 11815 © 2016 Cherry Aerospace DESCRIPTION The Cherry® G695B riveter is a compact, right angle riveter designed for high productivity, reliable installation of the short grip double action ® Cherrylock fasteners (NAS1738 / NAS1739 bulb and NAS1398 / NAS1399 wiredraw types). -
Page 4: General Operation Safety Warnings
TM-G695B Rev.: D DCR# 16-0786 DATE: 10/13/16 Federal Identification Code: 11815 © 2016 Cherry Aerospace SAFETY WARNINGS • Wear proper PPE when operating, servicing or repairing this tool (Personal Protection equipment) • Read Manual; operators must be trained in safety and correct tool operation •... -
Page 5: Fastener / Pulling Head Selection
PULLING HEAD SELECTION FOR BLIND FASTENERS • The lists given below are for reference only; for more up to date and detailed information, please check on the Cherry Aerospace webpage as following: Installation Tooling Manuals(links to current tool manuals) and... -
Page 6: Lockring Anvil Setting Adjustment
DCR# 16-0786 DATE: 10/13/16 Federal Identification Code: 11815 © 2016 Cherry Aerospace LOCKRING ANVIL SETTING ADJUSTMENT Note: All the item numbers refer to the exploded view from page 10. 1. Insert the short end of the setup gage into the nosepiece (C). -
Page 7: Service Procedure
TM-G695B Rev.: D DCR# 16-0786 DATE: 10/13/16 Federal Identification Code: 11815 © 2016 Cherry Aerospace SERVICE PROCEDURE HEAD SUBASSEMBLY Disassembly Instructions: • Remove the bleed screw (38) and drain the fluid. • Loosen set screw (20) and remove the pulling head. -
Page 8: Component List
TM-G695B Rev.: D DCR# 16-0786 DATE: 10/13/16 Federal Identification Code: 11815 © 2016 Cherry Aerospace G695B – COMPONENT LIST PART DESCRIPTION QTY. PART DESCRIPTION QTY. P604 O-Ring P463 Pipe Plug Dryseal P603 Back-Up Ring P225 Button Hd. Soc. Screw P528... -
Page 9: Exploded View
TM-G695B Rev.: D DCR# 16-0786 DATE: 10/13/16 Federal Identification Code: 11815 © 2016 Cherry Aerospace G695B – Exploded View... -
Page 10: Priming The Hydraulic System
TM-G695B Rev.: D DCR# 16-0786 DATE: 10/13/16 Federal Identification Code: 11815 © 2016 Cherry Aerospace PRIMING THE HYDRAULIC SYSTEM RECOMMENDED HYDRAULIC FLUID Specific gravity: 0.863 The riveter is supplied with Dexron® III ATF type “A”. Weight per gallon: 7.18 lbs. -
Page 11: Bleeding Instructions
TM-G695B Rev.: D DCR# 16-0786 DATE: 10/13/16 Federal Identification Code: 11815 © 2016 Cherry Aerospace PRIMING AND BLEEDING THE TOOL After service, the riveter must be primed with hydraulic fluid before re-assembling the head cylinder. • Stand the base upright and fill the base handle (56) with fluid up to the top then assemble and tighten the manifold.
Need help?
Do you have a question about the CHERRYLOCK G695B and is the answer not in the manual?
Questions and answers