Set the IP ............................... 11 Auto set the IP by the DHCP server ....................11 Configuration Guide ..........................12 Start and Login ............................12 Status ..............................13 Overview ............................. 13 Firewall ............................... 13 Routes ..............................14 2 CR-1010 User Manual Rev.01 082017...
Page 3
Reboot ..............................18 Service ..............................19 Dynamic DNS ............................. 19 Network Shares ........................... 19 Network ............................... 20 Interfaces ............................20 Wifi ..............................20 Switch ..............................21 DHCP and DNS ..........................21 Hostnames ............................22 3 CR-1010 User Manual Rev.01 082017...
UMTS/HSPA+ GSM/GPRS/EDGE Quad‐ Band WLAN to comply with 802.11n/802.11g/802.11b/802.113/802.113u 4 CH 10M/100M Ethernet ports DHCP server, DHCP serve static IP address Support RTC/CTS protocol Support TCP/IP,DHCP, ICMP protocol Web management and configuration General features Dual‐Band UMTS/HSPA+ Quad‐Band GSM/GPRS/EDGE Signal strength and Status indicators (LED) Control via AT commands and GUI Interface SIM card (1.8V/3.0V interface) SMA External antenna connecter Industrial grade components Automatic connection, Keep alive, Watchdog Transparent (TCP/UDP) WIFI SSID broadcast, Wireless 2.4GHz 300Mbps Wireless encryption : WPA, WPA2, WPA‐PSK, WPA2‐PSK Wireless MAC address filtering : support whitelist VLAN settings, Transmit power setting WDS function, Number of wireless clients limit, QoS:WMM Kick out weak signal device, disable weak signal device access 5 CR-1010 User Manual Rev.01 082017...
Page 6
Temperature checking (Optional) RF Specifications RF Module: SIM5360J Dual‐ Band UMTS/HSPA+ 800(850)/2100MHz Quad‐ Band GSM/GPRS/EDGE 850/900/1800/1900MHz GPRS multi slot class 12 EDGE multi slot class 12 WCDMA 3GPP release 5 Output power UMTS 850/2100 : 0.25W GSM 850/GSM900 : 2W DCS 1800/PCS1900 : 1W Specifications for GPS CELL assistant Location (No GPS) A‐ GPS : MS‐ Based, MS‐ Assisted Stand‐ alone GPS/QUALCOMM XTRA GPS mode GLONASS Ethernet 4 Ethernet Ports, 1 WAN Port (RJ45) Full Duplex 1 USB Port (AIRCARD Support) Communication Interface RS‐232, RS485 Selectable RS‐232 Serial interface (RJ45) Baud rate : 1200‐115200bps Parity bits : 8N1, 8O1, 8E1 6 CR-1010 User Manual Rev.01 082017...
Page 7
WCDMA 64Kbps CSD for Video call Other features Data/SMS/MMS/Voice and Fax UDP,TCP/IP,FTP/FTPS/HTTP/HTTPS SMTP/PPP/POP3/DNS/FOTA/eCall Power Supply DC 10‐30V 1A / AC 110‐240V Environmental Operating temperature ‐ 25C°to+70C° Storage temperature ‐ 40C°to+85C° Operating relative humidity 5 to 95% RH Dimensions 55 W x D 100 x H 130 mm. Mounting DIN rail mounting 7 CR-1010 User Manual Rev.01 082017...
Page 8
Network,WAN port, LAN Ports Button Reset Resetting Factory Default / Reboot 10 – 30 Vdc, polarity dependent, reverse polarity Power Input protection over-current protection, removable Power Supply industrial terminal block Power Consumption 250mA @ 12V(max) 8 CR-1010 User Manual Rev.01 082017...
Front Panel Front panel provide the power connecter, console port , Ethernet ports , GSM /GPS antenna and LED Status. Back Panel Back panel provide the DIN rail mounting for installation. 10 CR-1010 User Manual Rev.01 082017...
Page 11
USB (Aircard) LAN Port (4 Ports) LED Status WiFi Antenna SIM Card and SD Memory Card 11 CR-1010 User Manual Rev.01 082017...
IE 5.0 or higher version Install Condition When you install the router, please refer the below Put the device horizontally Keep away from any heat deice Do not put it in some place which is too dirty or too humidity TCP/IP Configuration Before using the device, you need to configure the network correctly, this manual is based on the Windows2000/XP/7, the IP of the device is 192.168.1.1 ,subnet mask is 255.255.255.0 Connect your PC to the LAN port and then you can configure the IP of your PC in 2 ways. Set the IP Set your PC’s IP as 192.168.1.xxx (xxx could be any number in 2‐254) subnet mask to be 255.255.255.0, default gateway 192.168.1.1 , DNS server 192.168.1.1 Auto set the IP by the DHCP server Set the TCP/IP to automatically get IP address , after setting, you could use the ping command to Check if the device has connected to the PC. For an example, in Windows 2000 run the cmd.exe , and the enter ping 192.168.1.1 if the screen show as the below, means OK, The device connected to the PC. 12 CR-1010 User Manual Rev.01 082017...
System > Hostname, Model, Firmware Version, Kernel Version, Local Time, Uptime, Load Average Memory > Total Available, Free, Cached, Buffered Network > The connection status of the WAN port. DHCP Leases > Show the IP address, MAC Address, and the Lease time remaining. Wireless > It is about the wireless status, will included SSID, Mode, Work Channel, Bitrate, BSSID and the Encryption of the transmission. Firewall The firewall tag, you could check the firewall status of the device. 14 CR-1010 User Manual Rev.01 082017...
Processes The Progresses, you could check an overview over currently running system processes and their status. Such as CPU usage, Memory usage. You could hang up, terminate or even kill the program, depends on your requirements. 16 CR-1010 User Manual Rev.01 082017...
System The System tag, could check and edit some basic information of the device, including Local time, Hostname, Timezone and Time Synchronization (NTP) 17 CR-1010 User Manual Rev.01 082017...
Software The software page, you could download and install the package, do not operate it without a professional engineer. Startup The Startup page, you can enable or disable installed init scripts here. Changes will applied after a device reboot, do not operate it without a professional engineer. Scheduled Tasks The Scheduled Tasks is the system crontab in which scheduled tasks can defined , do not operate it without a professional engineer. Mount Points Do some edition about the system, do not operate it without a professional engineer. 18 CR-1010 User Manual Rev.01 082017...
DHCP and DNS The DHCP and DNS mode , you could edit or setting network mode. , do not operate it without a professional engineer. 22 CR-1010 User Manual Rev.01 082017...
Static Routes You could setting and edit the IP Static Routes. , do not operate it without a professional engineer. 23 CR-1010 User Manual Rev.01 082017...
Need help?
Do you have a question about the CR-1010 and is the answer not in the manual?
Questions and answers