Related Manuals for Hanwha Vision SPA-C100B
Summary of Contents for Hanwha Vision SPA-C100B
- Page 1 IP AUDIO SYSTEM User Manual SPA-C100B/SPA-C100W SPA-C110B/SPA-C110W SPA-W100B/SPA-W100W SPA-H100B/SPA-H100W SPA-P100B/SPA-P100W SPA-D1000...
- Page 2 ※ Appearance, specification, etc. of the product is subject to change for performance improvements without prior notice. The latest update is available on the official Hanwha Vision website. (www.HanwhaVision.com) ※ The ID for the initial login is “admin, ” and a password should be set.
- Page 3 overview WARNING CAUTION TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
- Page 4 overview IMPORTANT SAFETY INSTRUCTIONS 22. Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area. 1. Read these instructions. 23. Do not place this apparatus near conductive material. 2. Keep these instructions. 24.
-
Page 5: Table Of Contents
Names and Functions of the IP Audio Operation Mode Module (SPA-D1000) System Settings Names and functions of the IP speakers Maintenance (ceiling-mount type) (SPA-C100B/ SPA-C100W) Names and functions of the IP speakers (ceiling-mount type, flame retardant structure / Plenum rate) (SPA-C110B/ SPA-C110W) -
Page 6: Names And Functions Of The Ip Audio Module (Spa-D1000)
NAMES AND FUNCTIONS OF THE IP AUDIO MODULE (SPA-D1000) NAMES AND FUNCTIONS OF THE IP SPEAKERS (CEILING-MOUNT TYPE) (SPA-C100B/SPA-C100W) Side a b c ALARM PoE+ GND IN ALARM STAT PoE+ GND IN RESET STAT RESET AL AR GN D —... -
Page 7: Names And Functions Of The Ip Speakers (Ceiling-Mount Type, Flame Retardant Structure / Plenum Rate) (Spa-C110B/ Spa-C110W)
NAMES AND FUNCTIONS OF THE IP SPEAKERS (CEILING-MOUNT TYPE, FLAME RETARDANT STRUCTURE / PLENUM RATE) (SPA-C110B/ SPA-C110W) Name Function Description Screw A screw for securing the speaker terminal cover. Safety cable hook Secures the speaker during installation to prevent it from falling. Audio module Equipped with an audio module. - Page 8 overview NAMES AND FUNCTIONS OF THE IP SPEAKERS (WALL-MOUNT TYPE) (SPA-W100B/SPA-W100W) Name Function Description Gasket Dustproof/waterproof gasket. Speaker terminal cover Covers the speaker terminal. Used for earth-grounding. Grounding port Grounding serves to protect the product from lightning strikes. Before connection, be sure to turn off the power of the device. Screw A screw for securing the speaker terminal cover.
-
Page 9: Names And Functions Of The Ip Speakers (Horn Type) (Spa-H100B/Spa-H100W)
NAMES AND FUNCTIONS OF THE IP SPEAKERS (HORN TYPE) Name Function Description (SPA-H100B/SPA-H100W) Gasket Dustproof/waterproof gasket. Audio module Equipped with an audio module. Used for earth-grounding. Grounding port Grounding serves to protect the product from lightning strikes. Before connection, be sure to turn off the power of the device. MicroSD card slot is not available. -
Page 10: Names And Functions Of The Ip Speakers (Pendant Type) (Spa-P100B/Spa-P100W)
overview NAMES AND FUNCTIONS OF THE IP SPEAKERS (PENDANT TYPE) Name Function Description (SPA-P100B/SPA-P100W) Used for earth-grounding. Grounding port Grounding serves to protect the product from lightning strikes. Before connection, be sure to turn off the power of the device. Speaker terminal cover Protects the speaker terminals. -
Page 11: Broadcast System Configuration Diagram
BROADCAST SYSTEM CONFIGURATION DIAGRAM Speaker Mode Block Diagram You can run a scheduled broadcasting, BGM, or TTS broadcasting using each speaker by itself. Controller Mode Block Diagram It is a block diagram for using the IP speakers in a controller mode. The controller mode speaker provides an operating GUI which is different from a regular speaker, and it can control multiple speakers via the button mode or event &... -
Page 12: Connecting To Power And A Network
overview CONNECTING TO POWER AND A NETWORK Network Cable Specification Item Contents Remark Connect the switching hub that supports PoE or PoE+ to the NETWORK port of the product using a network cable. If you connect the product to a switching hub that supports PoE+ or PoE, you can use it without a separate power Connector RJ45 (10/100BASE-T) source. -
Page 13: Starting
A speaker or an audio module is powered by PoE/PoE+. Use a switching hub that supports PoE or PoE+. The Device Manager Program ( ) is available on the official Hanwha Vision website (https://www.HanwhaVision.com) The IP microphone can receive power via PoE, or the DC power adapter can be used. - Page 14 8.8.4.4). You can update to the latest firmware for the product using the device manager. Check the firmware distribution information for each product on the Hanwha Vision website (https://www.HanwhaVision.com) and download the latest firmware (modelname_version.imkp) to your PC. You can also download the latest firmware to your PC from Device Manager.
- Page 15 2. When the firmware update is completed and the system is rebooted, the status will change to <Please wait Registering with the product’s initial IP address until the program starts.>. After it reaches 100%, it will change to <Success> If you connect only one product to the switch hub, it is possible to set up the password even on the web 3.
-
Page 16: Logging In
start LOGGING IN A maximum of five users can log in to the product at the same time. The <Exceed the maximum user> screen will appear if there is an attempt to log in while the maximum number of users are logged in, and it will show the currently Use the password set for the admin account. -
Page 17: Environment Settings
If you forgot the previous password, the product has to be initialized, and the passwords for all the 3. Select the upgrade file (model name_version.imkp) that you downloaded from the official Hanwha Vision accounts will be initialized during the process. - Page 18 environment settings - admin: You can use all the functions of the product. Setting the System Check Time - setup: You can use all the functions except for environment settings, such as System Upgrade, Sets the time for the system check. The system reboots automatically at the set time every day. Change Network, Change Time, etc.
-
Page 19: Network Settings
NETWORK SETTINGS Restarting System You can restart the system without disconnecting the power when a system reboot is needed. You can change the network settings according to the user's network connection configuration. 1. On the Home screen, click <Environment Setting> ; <Network Setting>. 1. -
Page 20: Time Settings
environment settings TIME SETTINGS 2. Click [Apply] to apply the set Time and Date information. Set the time and date accurately or it may cause problems in operating the broadcast. If the product is used in a local network environment without an external Internet connection, the time information may 1. -
Page 21: Device Operation Setting
DEVICE OPERATION SETTING Select the power and operation mode of the speaker and audio module. 4. For the speaker, you can select one of two operational modes depending on its usage. ~ Controller: You should register only one controller speaker, and the rest should be set up in speaker mode. -
Page 22: Home Screen Configuration
~ Source Name: The name of the Source Device will be displayed. Go to the Official Website If you click <Hanwha>, the screen will move to the Hanwha Vision Official Website. ~ Source Type: The source type of the Source Device will be displayed. - Page 23 Output Device Audio Monitoring The speakers registered as the <Zone> of the area for broadcasting will be displayed in the Output Device You can monitor the status of the Output Device speakers registered in the <Zone> of the area to broadcast. list.
- Page 24 using controller mode ~ The output monitoring device can be controlled by clicking [Play] and [Stop]. Button Mode - The audio automatically stops 1 minute after it starts playing. You can broadcast either by selecting the buttons of the source device and output device connected to the product or by the set Event &...
- Page 25 ~ Source Control: BGM or TTS lists of the selected source device are displayed. ~ Group : You can select an output group among the set groups, and duplicate selection is also possible. When you select a zone speaker to broadcast and select <Start Broadcasting> or <Stop The selected group will be displayed as highlighted.
- Page 26 using controller mode ~ Event & Preset: If you select a CP number set in the <Event & Preset> menu, it will be activated. (Up to 16 supported) If you press the number which is set as Zone or Group mode on the microphone device during the broadcast of the sound source in <Button Mode>...
-
Page 27: System Settings
SYSTEM SETTINGS Control Mode When you run <Start Broadcasting>, <Stop Broadcasting> from the <Operate> ; <Button Mode>, you Registers the device, source, and zone and sets the Event & Preset and annual schedules. can control the zone devices with either the TCP or UDP method. If the system is initialized or the network setting (User, DHCP) is changed after you register the device, you should Depending on the UNICAST, MULTICAST setting of <Source Registration>... - Page 28 using controller mode ~ Transmission Method: If you select UNICAST, <Trans IP> will be deactivated, and the device’s IP address will be used. You can enter the <Port> number in the input window You can use the <Controller> mode speaker as the zone device after performing <Device Registration> as with other automatically or manually, and it should not overlap with another device.
- Page 29 Registering an RM Microphone ~ Transmission Method: If you select UNICAST, <Trans IP> will be deactivated, and the device’s IP address will be used. You can enter the <Port> number in the input window Register a microphone to broadcast via speakers. automatically or manually, and it should not overlap with another device.
- Page 30 using controller mode Register Zone Group Setting You can register the speaker to the <Zone> of the region for broadcasting. <Zone> refers to one speaker set You can set the <Zone> to be broadcast by grouping it. as an output device. 1.
- Page 31 All Event & Preset List PUSH MONITOR CHIME POWER NETWORK -6dB +3dB +6dB PUSH MONITOR CHIME VOLUME POWER NETWORK -6dB +3dB +6dB VOLUME MENU PRESET MENU ALARM PREV PRESET PoE+ NEXT ALARM PREV CHIME PoE+ NEXT STATUS RESET CHIME STATUS RESET TALK TALK...
- Page 32 using controller mode - If you select the IP address as the microphone, the model name of the <Device Name> will be Event Registration Setting displayed and the CP can be selected from button_1~5. If you press the Contact Closure Number from among the five buttons on the left side of the microphone and press the <TALK>...
- Page 33 Setting Local File Play Broadcasting Routing/DSP/Source Stream Settings When an event occurs, the BGM audio stored in the speaker which is selected as zone will be played. When an event occurs, you can broadcast the BGM sound source (mp3, wav) and TTS of the registered Local file playback does not support TTS sound sources, and is unrelated to the speaker's source source device to the designated zone.
- Page 34 using controller mode Annual Scheduler Schedule Setting Screen It is a screen where you can set schedules. Broadcast reservations can be set. With the scheduler, you can perform scheduled broadcasts to as many zones (output speakers) as you want If there are duplicate broadcast schedules (BGM, TTS audio source) at the same time, the schedule which is using the audio source of the speaker selected as a source device in the <Source Registration>...
- Page 35 3. Repeat: Select a day, a period, etc. you want to set. If you set up the <Once> or <Everyday> function, check that the set schedule is accurate on the [Weekly Calendar], ~ Select Day: During the set dates, it runs only on selected days of the week. If you select days of the [Daily Calendar] screen.
- Page 36 using controller mode ~ TTS: Enter sentences with the language to be used in the <Text for TTS> and select the language and Holiday Setup Event gender in Select Speaker. Click the [Holiday] button on the scheduler settings screen - Select language: English (US, GB), German, Spanish, French, and Russian are supported. and the <Holiday>...
-
Page 37: Maintenance
MAINTENANCE View Log You can check logs generated in the product. Failover History Management The log items are different for each product, and they are recorded when the log operation occurs. The failure history for the product can be input and managed. 1. -
Page 38: Home Screen Configuration
Shows language options supported on the website. (Korean, English supported) Go to the Official Website If you click <Hanwha>, the screen will move to the Hanwha Vision Official Website. You cannot use contact closure input with a speaker by itself. - Page 39 BGM Play You can register an audio file for broadcasting. Be sure to format the microSD card in FAT32 (file system) before inserting it into the speaker. NTFS and exFAT (file systems) are not supported. A microSD card capacity of up to 32 GB is supported (SDHC, MLC, Class 10 or higher). We recommend Sandisk and Transcend products.
- Page 40 using speaker mode BGM Streaming Broadcast Server Operation Information When you click the [Apply] button on <Broadcast Server Settings>, the server begins operation, and you - This is a function to directly transmit and play sounds that have been uploaded to BGM Play to speakers will be moved to the following screen which shows the source file list, playback information &...
- Page 41 5. <Client Connection List> displays the information of other connected speakers (Activated, Deactivated 1. Click <BGM Streaming> ; <Broadcast Client>. status) only if the speaker transmission method is set to Unicast. ~ Click the [Start], [Stop] buttons to select whether to operate the Broadcast Client. If you set the speaker transmission method to Multicast, the information of other connected speakers will not be displayed, but the sound source play function will run.
- Page 42 using speaker mode Chime File Management 4. Uploaded Chime files are displayed on <Chime File List> on the right side. Click the number of the source file to play through the PC speaker. If you broadcast TTS audio in the <Operate> ; <Button Mode> menu of the speaker used for the <Controller mode>, the chime sound source is provided at the start and end of the broadcast.
- Page 43 ~ When you enter a special character, please refer to the following content. DSP Settings - In the TTS input window, you cannot enter & or `. You can control the speaker's output volume and the microphone’s input volume. - You can enter ^ ( ) _ | ‘ “, but they are not converted to audio. - If @ # $ % = \ / * are located alone or in the middle of sentence or numbers, they will be converted to audio.
- Page 44 using speaker mode ❖ For the IP audio module (SPA-D1000), the Equalizer menu is provided so that its sound can be properly Annual Scheduler adjusted according to the characteristics of the connected analog speaker. A broadcast reservation can be set. The Equalizer menu is not provided as the DSP optimal value is reflected for each speaker model.
- Page 45 Schedule Setting Screen 3. Repeat: Select a day, a period, etc. you want to set. It is a screen where you can set schedules. ~ Select Day: During the set dates, it runs only on selected days of the week. If you select days of the week, <Everyday>...
- Page 46 using speaker mode ~ TTS: Enter sentences with the language to be used in the <Text for TTS> and select the language and ~ Repeat Option (Extension): Sets the set schedule to repeat on a weekly, monthly, or yearly basis. gender in Select Speaker.
- Page 47 Holiday Setup Event SIP Management When it is connected to the VoIP phone which uses the standard SIP protocol and IP PBX server, the voice Click the [Holiday] button on the scheduler settings screen on the VoIP phone can be played on the speaker. and the <Holiday>...
-
Page 48: Maintenance
using speaker mode 4. If you dial <User ID> on your VoIP phone and speak, it will be received by and played on the speaker. MAINTENANCE The <Status Detail> of the <User ID> account will display as "Running, Conversation," and if you hang up the phone, it will change to "Disconnected."... - Page 49 Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Hanwha Vision cares for the environment at all product manufacturing stages, and is taking measures to provide customers with more environmentally friendly products.