Advertisement
Quick Links
Advertisement
Related Manuals for Chinowing E11
Summary of Contents for Chinowing E11
- Page 1 2022.3 V1.0.2 www. chinowing. com...
-
Page 2: Table Of Contents
E11 Schematic diagram of network router components ........5 E11 and V21 wiring diagram ....................6 Use of LAN and serial ports ..................... 8 V21 video transmission and E11 routing IP address distinction ......8 LAN configuration using ....................9 Seiral configuration using ....................10 TCP seiral port connection using ................ -
Page 3: Main Module
The E11 network router is mainly designed for not enough interfaces of network image transmission，it provides three 100M LAN interfaces. Three network serial ports supports TTL,RS232 hardware level，network protocol which supports TCP server ，TCP client， UDP client，... - Page 4 For serial port data connection co n n e c t i o n E11 has three LAN interface， three serial port， serial port including one TTL,two RS232 level.If your level signal does not support TTL or RS232，you need to buy an additional converting RS232 level module.Please connect the modules according to the...
- Page 5 The E11 and V21 can be seamlessly connected. After taking out the V21 shell screws, align them with the E11 screw holes, and use M2*18mm screws to connect the two modules together. The schematic diagram is as follows: www. chinowing. com...
- Page 6 L4 is always on, indicating that the serial port self-test is normal, and off, indicating that the serial port is faulty; L5 flashes to indicate data transmission, and when it is off, there is no data transmission; www. chinowing. com...
- Page 7 TX+ Web camera or other device 1. E11 is connected to 7.4-24V DC power supply, and the POWER indicator light indicates that the transmitter is powered on normally; when the L2 indicator light is continuously on, it means that the LAN port self-test is normal working；...
- Page 8 E11 terminal are consistent. 3. Make sure that the RX of the flight controller corresponds to the TX of the E11, and the TX of the flight controller corresponds to the RX of the E11.
-
Page 9: V21 Video Transmission And E11 Routing Ip Address Distinction
192.168.168.19 E11 LAN*2 All the above IP addresses in the E11 can be logged in and accessed in the browser of the PC to modify the parameter configuration. In order to prevent users from problems such as not being able to search, not being able to ping, and not being able to open web pages in the application. -
Page 10: Lan Configuration Using
LAN configuration using 1. After the LAN port of E11 is connected to V21, two IPC devices can also be connected. If the computer needs to access two IPCs at the same time, the IPC and the local IP of the computer must be set to the same network segment. - Page 11 ⑥ Use streaming software such as VLC media player to capture and play video data.9 www.chinowing.com...
- Page 12 IP when streaming video. Change the local IP of the computer to the same network segment as the IP camera; ● It is recommended to set the ip network segment of the two LAN ports of E11 to 192.168.168.XX and V21 in the same network segment, so that the image and configuration data of the LAN port and video transmission can be obtained at the same time;...
- Page 13 com...
- Page 14 Chinese and English. ③The 3-way serial port setting corresponds to the E11 external interface: port 1 → TTL, port 2 → RS232, port 3 → RS232; if you need to change the baud rate as shown in the figure below, just enter the corresponding baud rate to save the setting, the baud rate supports 600 -230400bps;...
- Page 15 Working mode Serial port working mode supports TCP Server, TCP ④ Client, UDP, Httpd Client, WEB to Serial (Websocket) and other working modes. www. chinowing. com...
- Page 16 (air terminal) in the port of the ground terminal. If it is connected through the external interface of the device, the serial port signals at both ends of the E11 must be consistent, otherwise the communication cannot be performed. www. chinowing. com...
- Page 17 ⑥ Image transmission configuration, in the serial port configuration, you can click "jump" on the air end or ground end, and after clicking, it will automatically jump to the corresponding image transmission configuration login interface. Video Transmission Login Username: admin123 Password: admin123 www. chinowing. com...
-
Page 18: Tcp Seiral Port Connection Using
The factory default baud rate of the E11 serial port is 115200, you need to set the flight controller or other equipment to 115200, and you can also log in to the Web to change the baud rate of the E11 serial port; Use of virtual serial port connection... - Page 19 ● The network virtual serial port tool can be downloaded from the official website "www.chinowing.com" download center. ● When using the serial port on the computer side, the connection method needs to select the TCP Client mode to access the corresponding port communication of E11. www. chinowing. com...
-
Page 20: E11 Seiral Port Working Mode Independent Port Distinction
When E11 is used as a pair, connect to the LAN ports of the V21 air end and the ground end respectively, and communicate after the V21 establishes a link.When E11 leaves the factory, the serial port default baud rate is 115200, and the default IP address is configured;and the default IP address is... - Page 21 com...
- Page 22 IP of the TCP Server cannot be obtained Please confirm whether the local IP address is in the same network segment as the E11 serial port 4 ：The serial port cannot connect and communicate a. Pay attention to whether the baud rates at both ends are the same b.
- Page 23 com...
- Page 24 History version Version Date Description Author 2022.03.5 V1.0 Initial version 2022.03.15 V1.0.2 Release version www. chinowing. com...
Need help?
Do you have a question about the E11 and is the answer not in the manual?
Questions and answers