Chapter 5 Function Parameter Table .................43 Chapter 6 Parameter Description ................71 Group F00: Basic Function Group..........72 Group F01: Start-stop Control Group..........79 Group F02: Motor Parameter Group..........85 Group F03: V/F Control Group............88 MOTORTECH S.A. MOTORTECH S.A. -03- Mocbos® | Enertronica Santerno Mocbos® | Enertronica Santerno...
Page 3
7.8 Common Faults and Solutions..........157 Chapter 8 Communication Protocol ................159 8.1 Networking Mode ..............160 8.2 Interface mode..............160 8.3 Protocol Frame Format ............160 8.4 Function Protocol..............161 8.5 Communication Parameter Address........165 MOTORTECH S.A. MOTORTECH S.A. -04- Mocbos® | Enertronica Santerno Mocbos® | Enertronica Santerno...
MU 821.20/21 Manual Completo Rev.00 CFM90 YW900 User Manual C hapter 2 P roduct Information 11/04/2023 2.3 CFM90 Series AC Drive Table 2-1 CFM90 series model Power Capacity Rated Input Rated Output Adaptable Motor AC Drive Model (KVA) Current (A)
Braking unit unit mark C: With a brake unit Fig. 2-1 Name Designation Rules 2.2 Nameplate MODEL: CFM90 - 5.5- 4T Model of the A C driv e R ated i nput v oltage, INPUT: AC3PH 380V 50/60Hz 14.6A/20.5A frequenc y a nd c urrent...
Page 16
C ha ter t Infor ation 11/04/2023 Fig. 2-4 Outline dimension and installation size Ins tallation Hole S ize of the AC Drive Table 2-3 CFM90 AC drive’s outline dimensions and installation sizes Single-phase 220V series CFM90-0.7-2S Ø4 0.90 CFM90-1.5-2S CFM90 2.2-2S...
Page 17
100W ≥100Ω as standard 100W CFM90-2.2-2S ≥70Ω Three phase 380V series CFM90-0.7-4T 150W ≥300Ω CFM90-1.5-4T 150W ≥220Ω Built-in None as standard 300W CFM90-2.2-4T ≥220Ω CFM90-4.0-4T 300W ≥130Ω MOTORTECH S.A. MOTORTECH S.A. -20- Mocbos® | Enertronica Santerno Mocbos® | Enertronica Santerno...
Free from oil dirt, dust and metal powder. 3.1.2 Installation Location Tips Ensure that there is sufficient space around for heat dissipation when installed CFM90 series AC drives. Space reserved requirements as shown below: ≥100mm ≥100mm Single installation Upper row and lower row installation Fig.
Page 22
C hapter 3 Mec hanical and E lectric al Ins tallation 11/04/2023 3.1.3 Installation Precautions When you install CFM90 series AC drive, pay attention to the following: Reserve the installation clearances as specified in Figure 3-1 to ensure sufficient space for heat dissipation. Take heat dissipation of the other parts in the cabinet into consideration.
a) Degrade the motor insulation performance AC drive. and damage the motor in the long run. MOTORTECH S.A. MOTORTECH S.A. -25- Mocbos® | Enertronica Santerno Mocbos® | Enertronica Santerno...
Page 26
AC drive.Do not connect the grounding terminal to the neutral conductor of power supply. 5 The main circuit terminals and function Fig.3-5 main circuit terminals diagram CFM90 MOTORTECH S.A. MOTORTECH S.A. -28- Mocbos® | Enertronica Santerno Mocbos® | Enertronica Santerno...
Page 28
YW900 User Manual C hapter 3 Mec hanical and E lectric al Ins tallation 11/04/2023 6 Control circuit terminals and function GND HDI 3-6 CFM90 control circuit terminals diagram Function Description of Control Circuit Terminals Type Terminal Function Description Name 10.5V(±3%)
Page 29
Using twisted pair or shielded cable. The longest distance is 300 meters. communicate grounding 3.2.6.1 Dial C ode S witch F unction Des cription CFM90 Signal Switching Dial Code Switch Function Description J umpers F ac tory d efault Name F unc tion...
C hapter 4 Operation, Dis play and Application E xamples 11/04/2023 4.1 Introduction of the keypad You can modify the parameters, monitor the working status and start or stop the CFM90 by operating the operation panel, as shown in the following figure. ENTER Fig 4-1 Keypad N o te: It is necessary to use M3 screw or install bracket to fix the external keypad.
11/04/2023 4.2 Viewing and Modifying F unction C odes The operation panel of CFM90 inverter adopts three-level menu. The three-level menu consists of function code group (Level I), function code (Level II), and function code setting value (level III), as shown in the following figure.Figure 4-2 Operation procedure on the operation panel.
Deceleration time means the time needed if the AC drive speeds down from the maximum one (F00.03) to 0Hz. CFM90 series AC drives define four groups of acceleration / deceleration time, which can be selected by F04. The factory default acceleration/deceleration time of the AC drive is the first group.
Page 111
Model Acceleration ○ F07.05 0.0~3600.0s dependent time 4 CFM90 series define 4 groups of Acc/Dec time which can be selected by F04 group. The first group of Acc/Dec time is the factory default one. Function Setting Range Property Name Default...
Page 132
Multi-stage speed can be set continuously in the range of -fmax ~ fmax. CMF90 AC drives can set 16 stages speed, selected by combination of Multi- stage terminals 1~4, corresponding to Multi-stage speed 1 to speed 15. MOTORTECH S.A. MOTORTECH S.A. -137- Mocbos® | Enertronica Santerno Mocbos® | Enertronica Santerno...
Page 145
11/04/2023 Chapter Maintenance and Troubleshooting 7.1 Routine Repair and Maintenance of the CFM90 7.1.1 Routine Maintenance The influence of the ambient temperature, humidity, dust and vibration will cause the aging of the devices in the AC drive, which may cause potential faults or reduce the service life of the AC drive.
Page 154
BPS. The settings of communication parameters see F0B functional group. 8.3 Protocol Frame Format MODBUS protocol includes two kinds of transmission modes (RTU mode and ASCII mode). CFM90 drives only support TRU mode, the corresponding date format such as the followings.
Page 163
Users can register by reading drive model to understand the type of inverter, CFM90 models 0xD090. Manufacturers of bar code for maintenance and management of the inverter manufacturers for recording.
Page 164
(4) MO D B U S C o mmu nic a tio n Illu s tr a tio n It is assumed that the CFM90 AC drive is set to the communication command control mode, MODBUS start AC drive with 30.00Hz frequency reverse runn- ing and observe the running state.
Need help?
Do you have a question about the CFM90 and is the answer not in the manual?
Questions and answers