Page 1
Parabolic sensor DBS 30 SONOCHEK Operating Instructions Series: SON 6.001 Issue: 14.09.18 Item number: LIT 06.201.EN Translation of the German manual...
Page 2
MANUFACTURER Fluke Deutschland GmbH Freisinger Str. 34 85737 Ismaning, Germany + 49 89 99616-0 www.pruftechnik.com Legal notices The product described in these instructions and this manual are copyright protected. The authors reserve all rights. The manual must not be copied, reproduced, translated or made available to third parties in any other form - in part or in full - without prior approval.
Content Notes about this document ........................5 General ............................5 Symbols Used ..........................5 Description of the parabolic sensor DBS30 ..................6 Applications and intended use ....................... 6 Functional principle ........................6 Sensor elements ..........................7 Sensor connections ........................8 Light spot target device ........................
Notes about this document Parabolic sensor DBS 30 Notes about this document 1.1 General These operating instructions describe the parabolic sensor DBS30 as an accessory for the ultrasonic measuring device SONOCHEK. These operating instructions contain important information regarding safe operation as well as all information for proper and efficient use. They must therefore be read prior to startup and all other steps.
Parabolic sensor DBS 30 Description of the parabolic sensor DBS30 Description of the parabolic sensor DBS30 2.1 Applications and intended use The parabolic sensor is used for precise detection of ultrasonic waves across distances of up to 25 m. The following test steps can be carried out in conjunction with SONOCHEK: ...
Description of the parabolic sensor DBS30 Parabolic sensor DBS 30 2.3 Sensor elements Sensor elements Parabolic mirror Light spot target device (changes possible in the course of device development, ’ see manufacturer s operating instructions) Parabolic mirror holder with set screw (on the back) Handle with control and display elements Status LED: Sensor on/off Target laser on/off (press and hold the button)
Parabolic sensor DBS 30 Description of the parabolic sensor DBS30 2.4 Sensor connections Connections Slot for sensor cable USB port (only for service) Red marking for sensor cable plug-in position SONOCHEK 09.2018...
Description of the parabolic sensor DBS30 Parabolic sensor DBS 30 2.5 Light spot target device Product element Height adjustment of the light spot Brightness control (5 levels red/green) R/G = Off Battery compartment Lateral adjustment of the light spot SONOCHEK 09.2018...
Parabolic sensor DBS 30 Description of the parabolic sensor DBS30 2.6 Device labeling / nameplate Labeling of the laser class: The laser safety warning label is affixed to the side of the parabolic sensor DBS30 handle. SONOCHEK 09.2018...
Page 11
Description of the parabolic sensor DBS30 Parabolic sensor DBS 30 The laser safety warning label for the parabolic sensor DBS30 with complying standard information is packed separately in a bag together with the pocket guides. The laser safety warning is attached to the side of the handle of the parabolic sensor DBS30. SONOCHEK 09.2018...
Parabolic sensor DBS 30 Operation of the parabolic sensor DBS30 Operation of the parabolic sensor DBS30 Eye injuries possible! The target laser (laser class 2) can cause serious eye damage. Never look into the laser beam. Never point the laser at other people or vehicles. Note that reflected laser light can also cause eye injuries upon extended exposure.
Operation of the parabolic sensor DBS30 Parabolic sensor DBS 30 3.2 Connecting the sensor to SONOCHEK Damage to the plug-in connectors possible! Note the mark with the red dot, which specifies the plug-in position on the bushing and plug. Connect any end of the sensor cable according to the red markings on the sensor ...
Parabolic sensor DBS 30 Operation of the parabolic sensor DBS30 3.4.3 Changing the battery Open the battery compartment with a suitable screwdriver. Exchange the battery. Observe the polarity as shown in the illustration. Close the battery compartment. 3.5 Cleaning and maintenance Incorrect cleaning and aggressive cleaning agents can damage the parabolic mirror of the sensor.
Disposal Parabolic sensor DBS 30 Disposal Electrical and electronic equipment may pose health and environmental risks if disposed of improperly. For this reason, it must not be disposed of as general household trash according to the WEEE directive 2012/19/EU (Waste Electrical and Electronic Equipment Directive), but rather must be handed over separately to designated collection points or sent back to the manufacturer.
Parabolic sensor DBS 30 Technical data Technical data The parabolic sensor is used for precise detection of ultrasonic waves across distances of up to 25 m. The following test steps can be carried out in conjunction with SONOCHEK: Detection of leaks on compressed air, gas and vacuum systems ...
Page 17
Technical data Parabolic sensor DBS 30 Sensor accessories Light spot target device, transport bag Optional accessories Sensor cable Laser type Semiconductor laser diode Laser beam power < 1.0 mW (according to IEC 60825-1:2014 condition 3) Laser beam divergence 2 mrad Maximum beam power <...
Need help?
Do you have a question about the Fluke DBS 30 and is the answer not in the manual?
Questions and answers