Related Manuals for Petol HYDRA-TORK U1344
Summary of Contents for Petol HYDRA-TORK U1344
- Page 1 PETOL™ HYDRA-TORK™ U1344, U1344L, U1344L-2B, U1344L14 Operating Manual © 2022 by PETOL GEARENCH. All rights reserved form U1344 revision 05/09/2022...
-
Page 2: Table Of Contents
Table of Contents PETOL™ U1344 HYDRA-TORK™ DESCRIPTION............3 PETOL GEARENCH LIMITED WARRANTY ............. 4 SAFE PRACTICES AND PROCEDURES ................5 ........................5 ESPONSIBILITY ......................6 EPLACEMENT ARTS ........................... 6 AFETY ........................6 RACTICES ......................7 AFETY RECAUTIONS ..................7 ESPONSIBILITY OF ISTRIBUTORS TONG CHAIN INSPECTION.................... -
Page 3: Petol™ U1344 Hydra-Tork™ Description
5,000 ft-lbs. The unit may be operated in any position (horizontal or inclined) and is totally portable. The PETOL Drill Pipe Tongs are adjusted to the different diameters within their range by adjusting the chain screw nut for fine adjustment and by adding or removing sections of chain for the coarse adjustment. -
Page 4: Petol Tm Gearench Limited Warranty
Law Applicable All matters related to the sale and/or use of the PETOL GEARENCH tool that is the subject of this limited warranty, along with the construction and enforcement of the terms of this limited warranty itself, shall be subject to the substantive and procedural laws of the state of Texas, not the conflicts of laws provisions of Texas, but rather the laws of Texas themselves. -
Page 5: Safe Practices And Procedures
Arbitration Clause In the event of dispute or claim arises out of the sale and/or use of the PETOL GEARENCH tool that is the subject of this limited warranty, or arises out of the interpretation or enforcement of the terms and conditions of this limited warranty, such dispute shall be submitted to binding arbitration pursuant to the rules of the American Arbitration Association. -
Page 6: Replacement Parts
Replacement Parts Use only PETOL™ replacement parts - no other parts are of comparable strength, quality and interchangeability. Safety While we pride ourselves on the quality and dependability that we build into PETOL™ GEARENCH tools and products, we caution users that it is only prudent to know and follow the simple rules of safety when using our products, or anyone else's. -
Page 7: Safety Precautions
12. Inspect chains frequently and regularly for link plate cracking, pin turning, pin protrusion and corrosion. 13. Use only PETOL™ replacement parts to ensure proper strength. Responsibility of Distributors IT IS THE RESPONSIBILITY OF THE PURCHASERS OF PETOL™ GEARENCH... -
Page 8: Tong Chain Inspection
Tong Chain Inspection The service life of leaf chains can be altered by a variety of adverse operating conditions. The following information discusses the most important of these conditions for consideration when operating or scheduling replacement of leaf chain systems. Overloading / Shock Loads / Side Loading Do not attempt to “inch loads which are beyond the rated capacity of the tool. -
Page 9: Normal Life Expectancy
Protection from corrosion is important in storage as well as in service. The factory lubricant applied to PETOL Chain is a “Fingerprint Neutralizing Water-Displacing Corrosion Preventative.” This is an excellent rust and corrosion inhibitor for chains in storage. -
Page 10: Periodic Inspection List For Petol Tm Special Chain
Periodic Inspection List for PETOL Special Chain... -
Page 11: Installation
Installation Location The PETOL™ HYDRA-TORK™ Unit should be located in an area with adequate room to work the downhole tools. The unit may be located indoors or outdoors upon solid ground or a finished shop floor. No special foundation is required. -
Page 12: Operation
Use a hydraulic pressure gauge on the power unit to indicate the system pressure in psi. The torque produced by the PETOL™ Drill Pipe Tongs is dependent on the hydraulic pressure. The torque produced in foot-pounds is the same as the pressure applied in psi (i.e. 2400 psi produces 2400 foot-pounds). -
Page 13: Chain Identification Guide
Chain Identification Guide... -
Page 14: Tong Adjustment
Tong Adjustment Warning! The pipe must NOT contact the flat side of the chain screw as shown above. Improper contact will cause premature breakage of the chain screw and could cause injury or death. If the flat side of the chain screw contacts the pipe, the chain MUST be lengthened by adding 2 pitches of chain. -
Page 15: Breaking Out
Do not exceed the rating of the tong. Consult with PETOL™ GEARENCH as needed for help with the toughest break out jobs. After the initial break out, ratchet the tong fully and then alternately extend and retract the cylinder until the connection is fully loosened. -
Page 16: Parts List
Of course, all replacement parts will be supplied by PETOL™ GEARENCH if you prefer to order from us. All tong, vise, and chain components are manufactured only by PETOL GEARENCH. DO NOT ATTEMPT TO SUBSTITUTE THESE COMPONENTS. The unit will not work properly unless these components are matched to the specific application. -
Page 17: Final Assembly
Final Assembly Item Part Number Description Notes UB1344 Base assembly U1344 only, see page 18 UB1344L Base assembly U1344L only, see page 18 UB1344L14 Base assembly U1344L14 only, see page 18 See page 19. 2 each for U1344 and DA1344 Drill pipe tong assembly U1344L. -
Page 18: Base Assembly
Base Assembly Item Part Number Description Notes HU75 Bushing HXN053 Eye nut McMaster-Carr 3274T42 or equal HXW016 Flat washer 1/2” HXN043 Hex nut, 1/2-13UNC... -
Page 19: Tong Assembly
Tong Assembly Item Part Number Description DH1344 Handle DJ1344 HP054 Jaw – handle pin w/ klipring HXKR062 Klipring only HP056 Spring pin w/ cotter HXC001 Cotter pin only HU74 Spring pin bushing HS01 Spring HG03 Spring guide HI08D Diamond point insert HP902 Insert key HS20SS... -
Page 20: Vee Saddle Assembly
Vee Saddle Assembly Item Part Number Description Notes UV1344-B Base UV1344-H Head McMaster-Carr HP373 Quick release pin 98320A255 or equal Hex bolt 5/16-18UNC x HXS012... -
Page 21: Cylinder Assembly
Cylinder Assembly Item Part Number Description Notes UC1344-C Cylinder Vickers/Aeroquip TG10CACA1AA06000 UHCH-F45 Reducer bushing Weatherhead C3109X8X6 (or equal) UHCH-Q05 Quick coupler UHCH-C4 Rod eye... -
Page 22: Chain Assembly
Chain Assembly Item Part Number Description As req’d 131-45-02 Special chain only As req’d 131-45-03 Special chain only As req’d 131-45-04 Special chain only HM03-45 Master link HP055 Rivet HV09-02-45 Chain screw assembly HV09-45 Chain screw only HN09 Chain screw nut As req’d HB63 Splice bolt with nut...