Ross MB-651 Installation And Cabling Manual

Rack Mounting
-65 1
| MB
Bri dge
Mo nito ring
SDI IN
4 x Rack Screws
Keep the following in mind when installing your MB-651:
• Install the MB-651 for maximum stability and adequate ventilation
• Ensure the MB-651 is installed in free air space where the ambient
temperature is monitored and controlled to not exceed 40°C (104°F)
at the frame front door
• Ensure that adequate space exists in front and behind the MB-651 and
on both sides of the frame
• The location of the MB-651 should be accessible, dry, and dust-free
MB-651 Physical Specifications
Clearance Side: 2.00" (50mm)
Rear: 3.00" (75mm)
Height 1.75" (4.45cm)
Width 19.00" (48.26cm)
Depth 8.5" (21.59cm)
Temperature maximum: 40°C
MB651DR-002-03
Printed in Canada.
© 2019 Ross Video Limited. Ross®, and any related marks are trademarks or registered trademarks of Ross Video Limited. All other trademarks are the property of their respective companies. PATENTS ISSUED and PENDING. All rights reserved. No part of this publication may be
reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechanical, photocopying, recording or otherwise, without the prior written permission of Ross Video. While every precaution has been taken in the preparation of this document, Ross Video assumes no
responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein.
MB-651 Installation and Cabling
Ethernet Cabling
Note:
network to ensure that there are no conflicts.
R
L T
DSE
4 HEA
3 UM E
2 VOL
1
t
Lt/R
SUM
8
7
6 MON ITOR
5
Note:
communications between the MB-651 and DashBoard. The figure below
shows all DIP Switches in the UP position (default).
SW1 Position
UP
UP
DOWN
DOWN
Specifications
Number of Inputs
Number of Outputs
Connector Type
Signal Level
Return Loss
DIP Switches Ethernet
SDI IN SDI OUT MONITOR GPIO
MODE ETHERNET PSU1 PSU2
Contact your IT Department before connecting to your facility
Leave the DIP Switches in their default positions to establish initial
1 2 3 4
SW1 and SW2 - Setting the IP Address
Description
SW2 Position
The IP configuration is set DashBoard. DHCP Mode is assumed
UP
until the user changes the settings in DashBoard. (default)
The MB-651 network settings are automatically assigned (DHCP
DOWN
Mode).
The MB-651 IP Address is set to 192.168.2.1 and the Subnet
UP
Mask is set to 255.255.255.0.
The MB-651 IP Address is set to 10.1.2.1 and the Subnet Mask is
DOWN
set to 255.255.255.0.
SDI Input and Output Analog Audio Monitor Output
1 Number of Outputs
1 Connector Type 3-pin terminal blocks
75ohm BNC Reference Level
800mV nominal Frequency Response +/-0.5dB 20Hz-20kHz
-10dB to 3G Distortion
Before you set up and operate your MB-651, refer to the "Important Regulatory and Safety
Notices" document that was included with your MB-651. It is also recommended to refer to
the MB-651 User Manual which is available for download from our website.
CAUTION
Power Cabling
SDI IN
Note:
The MB-651 powers on automatically when the power
supply is plugged in.
Video and Audio Cabling
SDI IN
SDI IN
Note:
For a -20dBFS input, there will be a +4dBu output.
GPIO Cabling
SDI IN
Note:
Shorting the I pin to the G pin will mute the front speakers,
and the audio level on the rear monitor ports will be controlled by
the front volume knob.
Power
2 Consumption 90-240VAC
50/60Hz
-20dBFS = +4dBu 90W
<0.01%THD+N
(20Hz-20kHz)
SDI OUT MONITOR GPIO
MODE ETHERNET PSU1 PSU2
Power
Monitor Ports
SDI OUT MONITOR GPIO
MODE
ETHERNET PSU1 PSU2
SDI OUT
SDI OUT MONITOR GPIO
MODE ETHERNET PSU1 PSU2
GPIO Port