Advertisement
Quick Links
OE STLYE RUNNING BOARD FOR TOYOTA RAV4 2019
Before Installation
Please read the instruction completely for easy installation, which will also help you to avoid
scratches or other potential damages to your appealing car.
The figures here are for reference only and may have differences with the actual product you
received, however they share the same assembly way.
Care and Cleaning
Mild soap may be used also to clean the Product.
Please periodically check and retighten all the hardware and clean the investment for a refresh
look.
Parts list
NO.
QTY
○
1
2
（left and right symmetry）
○
3
2
（left and right symmetry）
○
5
2
INSTALLATION INSTRUCTION S
PICTUER
Running Board
Center Bracket
Front Support Bracket
NO.
QTY
○
2
2
○
4
2
○
6
2
Page 1 of 15
PART#
WB01908011
PICTUER
Front Bracket
（left and right symmetry）
Rear Bracket
（left and right symmetry）
Rear Support Bracket
Advertisement
Related Manuals for WINBO WB01908011
Summary of Contents for WINBO WB01908011
- Page 1 INSTALLATION INSTRUCTION S PART# WB01908011 OE STLYE RUNNING BOARD FOR TOYOTA RAV4 2019 Before Installation Please read the instruction completely for easy installation, which will also help you to avoid scratches or other potential damages to your appealing car.
- Page 2 INSTALLATION INSTRUCTION S （left and right symmetry） （left and right symmetry） ○ ○ PVC washer M10 T-bolt （100*42） ○ ○ 10.5*26*2.5 Flat washers 65MN/10 Spring washers ○ ○ M10 nuts Plastic buckles ○ φ22 φ9 Plastic plugs Plastic plugs Page 2 of 15...
-
Page 3: Installation Steps
INSTALLATION INSTRUCTION S Installation Steps This installation instruction is just about one side installation method. The installation steps of left side and right side are the same. Step 1: Verify that all parts are present according to the manual and illustration. Step 2: .Open front and rear door as bellow picture;... - Page 4 INSTALLATION INSTRUCTION S Step 4: Remove 2 plastic buckles from the Chassis as bellow picture and keep them safe for the following installation. Step 5: Remove 8 plastic PLUGS from the Chassis as bellow picture. Page 4 of 15...
- Page 5 INSTALLATION INSTRUCTION S Step 6: Remove 2 bolts from side skirt and dissemble the side skirt off the chassis. Step 7: (1)take off one front fixing bolt (near the front wheel), meantime use this fixing bolt to install front support brackets to located place as bellow photo(do not tighten it up). Page 5 of 15...
- Page 6 INSTALLATION INSTRUCTION S (2) Use the original buckle which you had taken off before to lock up front support bracket as bellow picture and then tighten the bolt up. Step 8: Remove the Clips from the side skirt of the car and put them onto the products as bellow picture(total 11 pcs for one side) Page 6 of 15...
- Page 7 INSTALLATION INSTRUCTION S Step 9: BRACKETS INSTALLING Fine relevant holes under the chassis and follow bellow instruction to install front/center/rear bracket: Page 7 of 15...
- Page 8 INSTALLATION INSTRUCTION S (1) Front Bracket installs: Put the M10 T-Bolt to relevant holes and assemble T-bolt with PVC washer（100*42）as bellow picture: PVC Washer （ 100*42 ） After that, attach the brackets on the place as bellow picture and hold it with 65MN/10 spring washer and 10.5*26*2.5 Flat washer and M10 nuts;...
- Page 9 INSTALLATION INSTRUCTION S (2) Center Bracket Installs: Put the M10 T-Bolt to relevant holes and assemble T-bolt with PVC washer（100*42）as bellow picture: PVC Washer （ 100*42 ） After that, attach the brackets on the place as bellow picture and hold it with 65MN/10 spring washer and 10.5*26*2.5 Flat washer and M10 nuts;...
- Page 10 INSTALLATION INSTRUCTION S (3)Rear Bracket Installs: Put the M10 T-Bolt to relevant holes and assemble T-bolt with PVC washer（100*42）as bellow picture: After that, attach the brackets on the place as bellow picture and hold it with 65MN/10 spring washer and 10.5*26*2.5 Flat washer and M10 nuts; please do not fasten them up Page 10 of 15...
- Page 11 INSTALLATION INSTRUCTION S Step 10: Installation for the running board：Place the running board on the brackets and tighten it up by using spring washer, flat washer and nut; screw up the brackets and adjust the balance to perfect position. (front bracket) (Center bracket) (Rear bracket) φ22...
- Page 12 INSTALLATION INSTRUCTION S Step 11: Rear Support Bracket Installs: Remove the M6 fixing nut, spring washer and flat washer at the end of the running board and attach the rear support bracket on as bellow picture(please do not tighten the bolt up): At the same time, use the original buckle which you had taken off before to lock up rear support bracket as bellow picture and then tighten the bolt up Page 12 of 15...
- Page 13 INSTALLATION INSTRUCTION S Page 13 of 15...
- Page 14 INSTALLATION INSTRUCTION S Step 12: Restore Installation of the original screw and plastic buckle onto running board: Step 13: Putφ9 Plastic plugs to the hole position as bellow picture and complete the installation: NOTE Any damages and losses caused by improper installation and application, goes beyond our quality Page 14 of 15...
- Page 15 INSTALLATION INSTRUCTION S warranty. Page 15 of 15...