Important Safety Instruction 1. Read these instructions. Keep these Instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.. Do not install near any heat sources such as radiators, heat registers,stoves, or other apparatus (including amplifiers) that produce heat.
Page 4
“WARNING - To reduce the risk of fire or electric shock, do not expose the apparatus to rain or moisture.” “The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.” This symbol is intended to alert the user to the presence of uninsulated : dangerous voltage”...
Page 5
Do not use the unit against a bright back ground and where sunlight or other light sources will shine directly on the monitor. ▶ BE CAREFUL OF HEAVY OBJECT Neither the monitor itself nor any other heavy object should rest on the power cord. Damage to a power cord can cause fire or electrical shock. ……………………………………………………………………………...
NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 7
A. BOTTOM PANEL CONTROL 1. DC 12V IN 2. D-SUB IN PC Signal Input 3. VIDEO 1(AV1) IN Composite signal Input for AV1 4. VIDEO 1(AV1) OUT Video looping output for AV1 5. VIDEO 2(AV2) IN Composite signal Input for AV2 6.
B. REMOTE CONTROLLER 1. POWER( Turns the power ON or OFF. There will be a few seconds delay before the display appears. 2. SOURCE Select pc or video( PC / AV1 / AV2 / S-Video ) sources. 3. MUTE Mute the sound. 4.
1. SOURCE Select input source, and move the previous menu. 2. MENU Activates and exits the On Screen Display. This button can also be used to move previous menu or status. OSD MENU(MAIN) : Input Source, Screen, Audio, OSD, Color, Utility, Exit. 3/4.
…………………………………………………………………………… INSTRUCTION MANUAL 1. SELF-TEST DISPLAY When there is no connection at PC, the On Screen Display will show for 3 seconds. 2. OSD MENU DESCRIPTION : Input Source Select PC or AV1, SVIDEO.
Page 11
9 …………………………………………………………………………… : Screen : Brightness Increase or decrease the intensity of the image. : Contrast Increase or decrease the intensity (lightness or dimness) of the image. : H. position (PC Mode Only) Move image horizontally on screen right or left. : V.
Page 13
: OSD : H. Position Move the OSD position to right(▶) or left(◀). : V. Position Move the OSD position to up(▶) or down(◀). : Transparency Select the OSD background. : OSD Timer Select the OSD display timing. : Language Select a language among English, Français, Deutsch, Español, Danish, Italiano.
Page 14
: Color (PC Mode) : Color Temp Adjust color temperature to 9300, 6500, user. (note : 9300 is factory default) : Red Adjust red color for user. : Green Adjust green color for user. : Blue Adjust blue color for user. 13 ……………………………………………………………………………...
Page 15
: Utility : Recall Select to reset all setting to the factory default values. : Lock Select ON or OFF (ON : Control key lock. OFF : Control key unlock) : Exit H :15.7KHz V : 60.0Hz : Exit Turn off OSD Menu. ……………………………………………………………………………...
Page 16
Wall mountable using two methods: 1) Using the 200 mm pre-cut holes 2) Using the VESA standard wall mount design and the 100mm hole pattern on the back panel to install the LCD monitor to the wall. …………………………………………………………………………… INSTRUCTION MANUAL...
VESA DPMS(The display power management signaling) from a VESA DPMS video card. The VESA DPMS-compliant video card performs this signaling system through not sending horizontal, vertical, or sync signal. This monitor enters an appropriate mode through identifying each of the three modes of the signaling system. POWER CONSUMPTION...
“Going to Sleep” message on screen WEEE Symbols Correct Disposal of This Product (Waste Electrical &Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature,indicates that it should not be disposed with other household wastes at the end of its working life.To prevent possible harm to the environment or human health from uncontrolled waste...