Advertisement
Quick Links
Advertisement
Summary of Contents for Gemco ZLSP200A
- Page 2 O Energy Machinery Co., Ltd.: Professional Small Professional Small Anyang GEMC Anyang GEMCO Energy Machinery Co., Ltd.: Pell ll et M et Mil il l Ha l Handb ndb ook Catalogue Catalogue 1.0 Overview Overview ......................................
- Page 3 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook Overview 1.1 Acknow ledgement Dear customer, thank you for choosing our products, we are happy to provide you with satisfactory services. In order to fully develop the performance of the...
-
Page 4: Machin E Introdu Ction
Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook the machine before use according to this manual and the label on the machine. Add oi l and exert ru nn ing -in immedi atel y w hen operat in g machi ne. - Page 5 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook ZLSP200B 3phase 80-120 kg/h 215/245kg 950*450*1050mm 7.5KW 170-270 lbs/h 475/540lbs 37*18*41 inch ZLSP300B 3phase 250-350 kg/h 540/575kg 1350*750*1400mm 22KW 550-770 lbs/h 1190/1268lbs 53*30*55 inch ZLSP400B 3phase...
- Page 6 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook 180-265lbs/h 440-660 lbs/h 460/530 lbs 58*30*35inch 22 HP 120-200kg/h 300-400 kg/h 280/310 kg 1560*850*1000mm ZLSP230A 245-440lbs/h 660-880 lbs/h 620/680 lbs 61*33*39inch 35 HP 160-250kg/h 400-600 kg/h...
- Page 7 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook 11KW 120-200kg/h 300-400 kg/h 290/320 kg 1200*560*950mm ZLSP230C 245-440lbs/h 660-880 lbs/h 640/705 lbs 47*22*37inch 15KW 160-250kg/h 400-600 kg/h 340/370 kg 1240*580*1000mm ZLSP260C 350-550lbs/h 880-1300 lbs/h 750/815 lbs...
- Page 8 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook Name Name Round Nut Bearing Flat Washer Bearing Cover of Roller Hex Bolt Disc of Throwing Pellets Roller Shaft Dust Cover of Main Shaft Shaft Box...
- Page 9 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook 2.2.2 Stru ctur e and main parts of rol ler-turn ZLSP-R No. Name Name Upper Box Body Check Ring Shaft Box Grease Seal Bearing Seat Straight-through Oil Cup...
- Page 10 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook Roller Bearing Felt Main Shaft Cylindrical Roller Bearing Flat Key 2.3 Maint enance 2.3.1 Lubri cation Make sure oil is added to gearbox and all bearings are properly lubricated before initial operation.
-
Page 11: Getting Started
Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook 2.3.2 Inspecti on & m aintenance of the die and roll ers Inspection of Rollers: The roller should be visually inspected prior to each start-up. Make sure there are no foreign materials affecting roller running. - Page 12 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook Composition Both simple raw material and mixed material can be processed. Pieces of stone and iron or other hard substances cannot be mixed into the feedstock, or they will damage the machine.
- Page 13 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook reduced by thick material on die. When the clearance is less than 0.1mm, it will aggravate the wear and tear between die and rollers and shorten the service life.
- Page 14 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook the discharge scraper and die is 10-30mm. 3.3.4 How to adjust the clearance for ZLSP-D As shown in the following drawing. Shortly after starting the machine, feed a few materials and turn the adjusting bolts on both sides of the roller evenly until the die drives the roller to run.
- Page 15 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook 3.4.2 Setting up p rocedur es of di esel engi ne (By manual) “ ” 1. Turn the speed controller to the startup position. 2. Inset the starter crank into the hole of the startup shaft. Press down decompression handle with left hand.
- Page 16 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook 7. Set the throttle at the required position. 3.5 Preheatin g t he pellet mi ll 3.5.1 Before starting up each time, the machine needs to be preheated with an oily mixture repeatedly for 5 minutes or so.
- Page 17 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook into the pellet mill to preheat the machine . 2. Start up. 3. Feed oily mixture into mill and do not get feedstock out of the pelletizing chamber.
-
Page 18: Common Tro Ubles And Sol Utio Ns
Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook 4.0 Common tro ubles and sol utio ns Fault Cause Solution 1.New die has not been 1. Clean feedstock out of the ground by oily mixture or machine first and grind the ground insufficiently. - Page 19 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook products or parts to our factory for inspection. 5.2 Excepti ons 1. The machine is not purchased from us or an authorized franchisee of our company.
- Page 20 Anyang GEMCO Energy Machinery Co., Ltd.: Professional Small Pell et Mil l Handb ook Grease Felt retainer 2pcs roller seal Grease Felt retainer Main shaft seal Washer coupling Upper box Roller 1set body Upper box Mold(die) body 6.2 Main wearin g parts o f ZLSP-R...
Need help?
Do you have a question about the ZLSP200A and is the answer not in the manual?
Questions and answers