OTS SP-100D2 Manual

2 channel surface buddy phone

Advertisement

Quick Links

Undersea Systems International, Inc.
dba
Ocean Technology Systems
SP-100D2
2 Channel
Surface Buddy Phone
®
"Why Wait to Communicate?"

Advertisement

Table of Contents
loading

Summary of Contents for OTS SP-100D2

  • Page 1 Undersea Systems International, Inc. Ocean Technology Systems SP-100D2 2 Channel Surface Buddy Phone ® “Why Wait to Communicate?”...
  • Page 2 International, Inc., dba Ocean Technology Systems hereinafter referred to as OTS, reserves the right to change specifications without notice. It is recommended that all users read and fully understand this manual before using the SP-100D2. All statements, technical information, and recommendations herein are based on tests we believe to be reliable, but the accuracy or completeness thereof is not guar- anteed;...
  • Page 3: Table Of Contents

    Squelch ..................8 Reception ..................8 Transmission ................9 Recording Communications ............9 Helpful Hints................9 Section 5: Maintenance ................11 SP-100D2 Surface Buddy Phone ..........11 ® TCA-35 Transducer ..............11 HHM-3 Hand-Held Microphone ..........11 Batteries ..................11 Limited Warranty ..................12...
  • Page 4: Section 1: Introduction

    The SP-100D2 is the latest design of the SP-100 Buddy Phone, featuring innova- tive software-defined radio (SDR) technology that uses digital signal processing (DSP) algorithms. This new design represents the latest in state-of-the-art com- munications technology, with a streamlined hardware design;...
  • Page 5: Specifications

    SPECIFICATIONS Transmitter output power: 1/2 watt PEP (peak envelope power) Audio output to speaker: 1/2 watt (nominal) Modulation: Single sideband, no carrier Operating channels: Freq. A (Channel 1): 32.768 kHz USB Freq. B (Channel 4): 31.250 kHz LSB Power supply: Sixteen AA alkaline cells Battery life: 20 hours (nominal)
  • Page 6: Section 2: Functions

    SECTION 2 FUNCTIONS Figure 1 depicts the SP-100D2 panel. The numbered text below is the key to the indicated items in Figure 1. Text in all capital letters refers to the label on the panel. VOLUME: Use the volume control to adjust the front-panel speaker listening volume.
  • Page 7 Figure 1...
  • Page 8: Section 3: Batteries

    LOW-BATTERY ALERT The SP-100D2 is equipped with a unique low-battery alert. As the battery level decreases, you will start to hear a short three (3) tone burst, then says “Low Bat-...
  • Page 9 WARNING! If you are going to ship the SP-100D2, remove the batteries first to prevent damage to the holders in the event the unit is dropped. Furthermore, all batteries should be removed if you intend to store the SP-100D2 for an ex- tended time.
  • Page 10: Section 4: Operation

    SECTION 4 OPERATION The SP-100D2 is designed to be portable and easy to operate. It is an ultrasonic, through-water communication system. It will enable you to talk to all other divers and/or surface stations on the same frequency and within range. When you speak using the SP-100D2, your voice is sent out in an omni-directional pattern via the transducer to all other transceivers.
  • Page 11: Adjustments And Controls

    The voice recognition capabilities of the SP-100D2 allow it to activate the panel speaker with even the slightest voice in the greatest noise, such as that found on an active reef. Therefore, the SP-100D2 squelch does not suffer the loss of range encountered with other squelch systems, especially in high-noise environments.
  • Page 12: Transmission

    • Inform the divers that if they go below a thermocline, they should inform ev- eryone. If possible, lower the transducer to the same depth as the divers in the thermocline. • If you are using the SP-100D2 on a vessel, always remember to pull up the...
  • Page 13 • Keep the hand-held microphone as dry as possible. It is not waterproof. • Place the SP-100D2 where it can be heard easily. If working on a boat, locate a place where you can secure the unit where boat action will not cause it to fall.
  • Page 14: Section 5: Maintenance

    Warm water with a small amount of nonabrasive soap is the recommended clean- ing solution. When the SP-100D2 is not being used, it is a good idea to keep the cover securely fastened. Remember, when the transducer assembly is connected to the SP-100D2, the power is on.
  • Page 15: Limited Warranty

    Ocean Technology Systems factory-trained service center or properly trained personnel. In no event shall Ocean Technology Systems be liable for consequential damages. You can now register your product online at the OTS Web site. Just visit http://www.oceantechnologysystems.com/register1.html. Undersea Systems International, Inc.
  • Page 16 NOTES:...

Table of Contents