1. Manuals
  2. Brands
  3. Elsner Manuals
  4. Light Fixture
  5. Cala KNX IL
  6. Installation and adjustment

Elsner Cala KNX IL Installation And Adjustment

Indicator light green/yellow/red
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
EN
Cala KNX IL (CO2)
Indicator Light Green/Yellow/Red
Item numbers 71380 (Cala KNX IL) and 71390 (Cala KNX IL CO2)
Installation and Adjustment

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Cala KNX IL and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Elsner Cala KNX IL

  • Page 1 Cala KNX IL (CO2) Indicator Light Green/Yellow/Red Item numbers 71380 (Cala KNX IL) and 71390 (Cala KNX IL CO2) Installation and Adjustment...

  • Page 3: Table Of Contents

    5.8.2. AND logic connection inputs ..............27 5.8.3. OR LOGIC connection inputs ..............28 Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany Cala KNX IL light signal • from application 1.0 Status: 04.04.2023 • Technical changes and errors excepted.
  • Page 4 The change status (software version and date) can be found in the contents footer. If you have a device with a later software version, please check www.elsner-elektronik.de in the menu area "Service" to find out whether a more up-to- date version of the manual is available.

  • Page 5: Safety And Operating Instructions

    Description The LED area of the Cala KNX IL LED light signal can illuminate or flash in the col- ours green, yellow or red. This allows states to be visualised for the KNX bus system.

  • Page 6: Commissioning

    The programming button can be reached through the opening on the rear of the hous- ing; it is recessed. Use a thin object to reach the button, e.g. a 1.5 mm² wire. Cala KNX IL light signal • Version: 04.04.2023 • Technical changes and errors excepted.

  • Page 7: Transmission Protocol

    Light signal status colour yellow R-CT- [1.1] DPT_Switch 1 Bit signal On/Off Output light Light signal status colour green R-CT- [1.1] DPT_Switch 1 Bit signal On/Off Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.
  • Page 8 PeriodSec Output CO2- CO2-GW 1 switch output R-CT- [1.1] DPT_Switch 1 Bit GW 1 Input CO2-GW CO2-GW 1 switch output lock -WC-- [1.1] DPT_Switch 1 Bit Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.
  • Page 9 CO2 controller setpoint (1:+ | 0:-) -WC-- [1.2] DPT_Bool 1 Bit troller 104 Output CO2 CO2 controller setpoint ventila- R-CT- [5.1] DPT_Scal- 1 Byte controller tion Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.
  • Page 10 [5.1] DPT_Scal- 1 Byte ing variable 2: Input 4 comparator 132 Input actuat- Actuating variable comparator -WC-- [5.1] DPT_Scal- 1 Byte ing variable 2: Input 5 comparator Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.
  • Page 11 AND logic 3: 1 bit switching out- R-CT- [1.2] DPT_Bool 1 Bit Logic 166 Output AND AND logic 3: 8 bit output A R-CT- depending on 1 Byte Logic setting Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.
  • Page 12 OR logic 4: 8 bit output B R-CT- depending on 1 Byte Logic setting 188 Input OR Logic OR logic 4: Block -WC-- [1.1] DPT_Switch 1 Bit Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.

  • Page 13: Setting Of The Parameters

    Off • On valid until the first communication Set the brightness of the light signal after a reset. Brightness 0…100 % valid until the first communication Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.
  • Page 14 1 x scenario object: Set the scenario numbers. In case of pre-set values, Cala KNX IL does not light up at all for scenario number 1, lights up green for scenario number 2, yellow for 3 and red for 4.
  • Page 15 Set the limit value for colour change from green to yellow. You can specify the thresh- old value via communication object no. 25 (light signal TV green/yellow) also. Start limit value for change from green to -6700000…6700000; 200 yellow [x 0.1] Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.
  • Page 16 Set the display behaviour of the red light signal. If the signal colour Red is active, the light • be permanently On signal should be • be permanently Off • flashing Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.
  • Page 17 = red Value for ‘Status colour RGB’ object in sta- #000000 ...#FFFFFF tus = Off (only for 3 x one-bit object and 1 x scenario object) Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.

  • Page 18: Co Measured Value

    Send cycle 5 s • 10 s • ... • 2 h (if sent periodically) Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.

  • Page 19: Co Threshold Values

    During initial commissioning, a threshold value must be defined which will be valid un- til the first call with a new threshold value. For units which have already been taken into Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.
  • Page 20 (TV = Threshold value) • TV below = 1 |TV + hysteresis above = 0 • TV below = 0 |TV + hysteresis above = 1 Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.
  • Page 21 The behaviour of the switching output during blocking can be set. Switching output behaviour On blocking • Do not send message • send 0 • send 1 Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.

  • Page 22: Co Pi Controller

    • 1 = Block | 0 = release • 0 = block | 1 = release Specify an object value until first communication. Blocking object value 0 • 1 before the first communication Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.
  • Page 23 During initial commissioning, a set point value must be defined which will be valid un- til the first Communication of a new setpoint value. For units which have already been Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.
  • Page 24 You should set the time appropriate to the ventilation system (follow the manufactur- er's instructions). Reset time in minutes 1...255; 30 Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.

  • Page 25: Variable Comparator

    The block can take effect at value 0 or 1, depending on the intended use. Assessment of the block object • at value 1: block | at value 0: release • at value 0: block | at value 1: release Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.

  • Page 26: Logic

    AND Logic 1 / 2 / 3 / 4 not active • active OR logic OR Logic 1 / 2 / 3 / 4 not active • active Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.

  • Page 27: And Logic 1-4 And Or Logic Outputs 1-4

    0 … 255 / 100% / 360° / 127; 0 monitoring time exceeded Output value object B if 0 … 255 / 100% / 360° / 127; 0 monitoring time exceeded Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.
  • Page 28 The behaviour of the output on release can be set. on release • Do not send message (with 2 second release delay) • transmit value for current logic status Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.

  • Page 29: And Logic Connection Inputs

    Logic input 7 inverted Logic input 8 Logic input 8 inverted Logic input 9 Logic input 9 inverted Logic input 10 Logic input 10 inverted Logic input 11 Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.

  • Page 30: Or Logic Connection Inputs

    Switching output AND logic 2 inverted Switching output AND logic 3 Switching output AND logic 3 inverted Switching output AND logic 4 Switching output AND logic 4 inverted Cala KNX IL light signal • Status: 04.04.2023 • Technical changes reserved. Errors reserved.
  • Page 32 Questions about the product? You can reach the technical service of Elsner Elektronik under Tel. +49 (0) 70 33 / 30 945-250 or service@elsner-elektronik.de We need the following information to process your service request: • Type of appliance (model name or item number) •...

This manual is also suitable for:

Cala knx il co27138071390

Table of Contents