Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CET ND65
Summary of Contents for CET ND65
- Page 1 ND65 LoRaWAN Gateway User Manual Version: V1.0A March 20, 2023...
- Page 2 CET Inc. (CET). The information contained in this manual is believed to be accurate at the time of publication; however, CET assumes no responsibility for any errors which may appear here and reserves the right to make changes without notice. Please consult CET or your local representative for the latest product specifications.
- Page 3 CET Electric Technology DANGER Failure to observe the following instructions may result in severe injury or death and/or equipment damage. ➢ Installation, operation and maintenance of the device should only be performed by qualified, competent personnel that have the appropriate training and experience with high voltage and current devices.
-
Page 4: Table Of Contents
3.2.2 Wi-Fi Connection ......................8 3.2.3 Cellular Connection ...................... 10 3.3 Packet Forwarder Configuration ..................... 11 3.4 Configure ND65 as a Network Server ..................15 Chapter 4 An Application Example ....................... 19 4.1 PMC-350-C device setup ......................19 4.2 ND65 Gateway Configuration ....................20 4.3 Troubleshooting ........................ -
Page 5: Chapter 1 Introduction
10km and can cover about 2km in urbanized areas, ideally suited for smart offices, smart buildings and many other indoor applications. In addition to supporting multi-backhaul backups with Ethernet, WiFi and cellular, the ND65 is compatible with popular network servers. It has an integrated network server and Milesight IoT Cloud for easy deployment. -
Page 6: Front Panel Led Indicators
Ethernet are not equipped), press and hold on the Reset button for more than 5 seconds. 2. Release the Reset button when the LED indicators blink. 3. When the LED indicators are all On again, the reset operation is completed, and the ND65 is reset to factory default. -
Page 7: Chapter 2 Installation
To take out the SIM card, push in the SIM card, and it will pop up automatically. Notes: The ND65 does not support hot plugging, and please turn off the power before inserting or taking off the SIM card. -
Page 8: Wiring Ethernet Cable & Power Cable
2.3.4 Mounting the ND65 The ND65 can be mounted to a wall or a pole. Before the installation, please make sure that the SIM card has been inserted, the antennas have been attached, and all cables have been installed properly. - Page 9 CET Electric Technology 2.3.4.2 Pole Mounting 1. Open the hose by turning the locking mechanism counterclockwise. clamp 2. Straighten the clamp, and slide it through the rectangular rings in the mounting hose bracket, and wrap the hose clamp around the pole.
-
Page 10: Chapter 3 Configure Device Via Web Server
CET Electric Technology Chapter 3 Configure Device via Web Server 3.1 Web Accessing The default IP addresses of the ND65’s Ethernet Port and WIFI are 192.168.23.150 and 192.168.1.1, respectively. 3.1.1 Wireless Access 1. Power on the ND65. 2. Enable Wireless Network Connection on your computer and search for access point “Gateway_******”... - Page 11 CET Electric Technology 2. Accessing Web Interface a) Enter the IP Address of the ND65 (e.g.: https://192.168.1.23) in the Address area of Google Chrome and then press <Enter>. b) The user must log in to the Web interface to view data or change setup parameters.
-
Page 12: Network Connection
2. Click Save & Apply and the changes will take effect immediately. 3. Connect the ND65 to a router or a modem via the Ethernet port. 4. Log in to the web page via the newly assigned IP address and click Status > Network to check the Ethernet port status, where up represents the Ethernet Port is enabled. - Page 13 CET Electric Technology 3. Select one WIFI and click Join Network. 4. Type the key of WiFi and click Save.
-
Page 14: Cellular Connection
CET Electric Technology 5. Click Status > WLAN to check WiFi connection status, where Enabled represents the ND65 is connected to the specified WiFi successfully. 3.2.3 Cellular Connection Click Network > Interface > Cellular on the left hand and click the Client tab. -
Page 15: Packet Forwarder Configuration
Click Status > Cellular to check the WiFi connection status. 3.3 Packet Forwarder Configuration The ND65 can function as a gateway and forward LoRaWAN data to the third party’s LoRaWAN network servers. Here illustrates how to configure ND65 as a gateway. - Page 16 CET Electric Technology number is 58A0CB800BE7, insert FFFE after the first 6 characters to make it a 16-character Gateway EUI (e.g., 58A0CBFFFE800BE7). 2. Click to add a network server. 3. Go to Packet Forwarder > Radio page to configure Antenna Type, Center Frequency and Channels.
- Page 17 CET Electric Technology Notes: 1. The following ISM Bands are supported on the ND65: N865/RU864/EU868/US915/AU915/KR920/AS923-1/2/3/4 2. The table below lists the supported ISM Bands and the corresponding channel assignments. ISM Band Channel (MHz) EU433 433.175, 433.375, 433.575, 433.775, 434.065, 434.265, 434.465, 434.665 CN470 471.9, 472.1, 472.3, 472.5, 472.7,472.9, 473.1, 473.3 (8~15)
- Page 18 CET Electric Technology 5. Click Traffic to view ND65’s data communication, where up represents uplinks while down means downlinks. Datarate: the rate at which data is transferred from one place to the other Coderate: the proportion of the data-stream that is useful...
-
Page 19: Configure Nd65 As A Network Server
CET Electric Technology 3.4 Configure ND65 as a Network Server The ND65 can function as a network server, retrieve node data, and then transmit data to other cloud platforms. Click Packet Forwarder > General on the left hand and make sure the embedded network server is enabled. - Page 20 CET Electric Technology 4. Click the Application tab to add a new application. 5. After saving the application, select HTTP, HTTPS or MQTT protocol and fill in corresponding server information to send data to another server.
- Page 21 CET Electric Technology 6. Click the Profiles tab to add a new profile for the device. 7. Click Add to add LoRaWAN ® node devices via the Device tab. in batches Click Bulk Import to add nodes...
- Page 22 CET Electric Technology Click Template Download to download the template file and add device information to this file. The application and device profile should be consistent with what you will create on the web page. 8. Click the Packets tab to check the packets from LoRaWAN ® node devices. The type UpCnf means uplinks, while DnUnc means downlinks.
-
Page 23: Chapter 4 An Application Example
Set the Wiring Mode and enable Auto-Push • ND65 Gateway Configuration Setup to make sure the PC and ND65 Gateway are in the same subnet LoRaWAN ND65 Gateway setup a) Set Network Server Mode b) Select a Region Radio Frequency... -
Page 24: Nd65 Gateway Configuration
CET Electric Technology 4.2 ND65 Gateway Configuration 1. Make sure the PC and ND65 Gateway are in the same subnet. Go to Control Panel > Network and Internet > Network and Sharing Center > Ethernet > Properties > Internet Protocol Version 4 (TCP/IPv4), and assign a static IP with the same... - Page 25 CET Electric Technology 2. Set up the ND65 Gateway. 1) Login to the ND65 Web GUI. Open the browser on the PC and enter the ND65 IP address into the address bar to access the ND65 web. 2) Enable localhost on the General tab under Packet Forwarder and click Save & Apply.
- Page 26 CET Electric Technology 5) Create the Device Profile. Define a name for the device on the Profiles tab under Network Server and select Class Type. Click Save. 6) Add devices to LoRaWAN. Click Add under the Device tab. b. Fill up the device information, and please refer to the label on the meter, like...
- Page 27 CET Electric Technology Go to Packets under Network Server to view the data status (sending/receiving). The Device EUI, communication frequency, sending time, data size and sending status are shown on Packets. The UpCnf indicates data packet uplink is confirmed. 3. Setup Cellular Connection.
- Page 28 CET Electric Technology 4. Check the cellular network status. Click on the Cellular tab under the Status, and the page of Modem Information and cellular Network Status of the Gateway will be shown.
-
Page 29: Troubleshooting
1. Ping. Login to the ND65 web and click Maintenance > Tools. Click Ping. The figure left indicates IP Ping works, ND65 sent 4 packets to the application server, and 100% received in about 250ms, while the figure right represents the application server failed to respond to IP Ping. - Page 30 CET Electric Technology Appendix A Technical Specifications Hardware Quad-core 1.5 GHz, 64-bit ARM Cortex-A53 Memory 512 MB DDR4 RAM Flash < 8 GB eMMC LoRaWAN Antenna Standard 2 × Internal Antennas Optional 1 × 50 Ω N-Female External Connector ISM Bands...
-
Page 31: Contact Us
CET Electric Technology Contact us CET Electric Technology Inc. Email: support@cet-global.com Web: www.cet-global.com...
Need help?
Do you have a question about the ND65 and is the answer not in the manual?
Questions and answers