KCFA SV-X3 Series Installation And Wiring

Installation and Wiring for SV-X3 Series Servo Motor
Hardware Instruction
Thank you for purchasing this product.
This manual mainly describes the safety use, installation and wiring
for SV-X3 series servo motor.
Fo r m o re details, please refer to < SV-X3 Series Ser vo D rive Instructio n
M anual> .
Co nfirm the fo llo wing item s when unpacking:
N um ber
1 Ser vo m o to r
Flat key
2 Accessories 4pin term inal
2pin term inal (Fo r m o to r with brake)
Installation and Wiring for SV-X3 Series Servo Motor Hardware Instruction
3
4 Certificate of Appro val
◎
Check if there are so m e dam age to the pro ducts during transpo rtatio n.
◎
Any questio ns, please co ntact the HCFA Co rpo ratio n.
Safety precautions
Please pay attentio n to the flo wing safety precautio ns anywhere and any tim e
during acceptance inspectio n, installatio n, wiring, o peratio n and m aintenance.
■ In this m anual, the safety precautio ns are ranked as " DAN G ER" and " CAUTIO N "
Indicates that incorrect handling may result in death or severe injury.
Indicates that inco rrect handling m ay result in m edium o r slight
perso nal injur y o r physical dam age.
Indicates " Pro hibitio ns" (Indicates what m ust no t be do ne.)
Indicates " Fo rced" .(Indicates what m ust be do ne.)
Installing and wiring
Do not connect the motor to the commercial power.
Do not place the combustibles around the servo motor and drive.
Be sure to protect the drives through the case,
and leave specified clearances between the case
or other equipment and the drive.
Install it at the place free from excessive dust and
dirt, water and oil mist
Install the equipment to incombustibles, such as metal.
Any person who is involved in wiring and inspection
should be fully competent to do the work.
FG terminal of motor and drive must be grounded.
Perform the wiring correctly after cut off the breaker.
Have the insulation processing when connecting
cables.
Operation and running
During operation, never touch the internal parts of the drive.
The cables should not be damaged, stressed
loaded, or pinched.
During operation, never touch the rotating parts
of the servo motor.
Do not install the equipment under the conditions
with water, corrosive and flammable gas.
Manual Number MQ075B065A01EN
M anual Version 1.3
Date M ay, 2019
N am e
DANGER
To prevent fire or malfunction.
To prevent fire.
To prevent electric shock,
fire or m alfunction.
To prevent electric shock,
fire , malfunction or damage
To prevent fire.
To prevent electric shock.
To prevent electric shock.
To prevent electric shock,
injury, malfunction or damage
To prevent electric shock,
fire or malfunction.
To prevent burns or electric shock.
To prevent electric shock,
malfunction or damage.
To prevent injury.
To prevent fire.
Do not use it at the location with great vibration
and shock.
Do not use the servo m otor with its cable
soaked in oil or water.
Operate the switches and wiring with dry hand.
Do not touch the keyway directly when using
the m otor with shaft-end keyway.
Do not touch the m otor and drive heat sink , as
they are very hot.
Do not drive the m otor by external drive.
Confirm the equipm ent' s safety after the
earthquake happens.
Installing and setting correctly to prevent the fire
and personal injury when earthquake happens.
Provide an external em ergency stop circuit to
ensure that operation can be stopped and
power switched off im m ediately.
Before wiring or inspection, turn off the power
and wait for 5 m inutes or m ore.
Please follow the specified combination of the
motor and drive.
Do not touch the terminals of connector directly.
Do not block intake and prevent the foreign
matters from entering into the motor and drive.
Fix the motor and have the test run away from the
mechanical system. After confirming the operation,the
motor can be securely mounted to mechanical system.
The servo motor must be installed in the
specified direction.
Q uantity
Install the equipment correctly in accordance with
1
its weight and rated output.
1
1 Do not climb or stand on servo equipment. Do
not put heavy objects on equipment.
1
The parameter settings must not be changed
1
excessively. Operation will be instable.
1
When power is restored after an instantaneous power
failure, keep away from the machine because the
machine may be restarted suddenly(design the machine
so that it is secured against hazard if restarted).
Keep it away from the direct sunlight.
Do not put strong impact on the motor, drive
and motor shaft.
The electromagnetic brake on the servo motor is
designed to hold the servo motor shaft and should
not be used for ordinary braking.
Do not install or operate a faulty servo motor or drive.
Check the power specification.
The electromagnetic brake may not hold the servo motor
shaft. To ensure safety, install a stopper on the machine side.
A sudden restart is made if an alarm is reset with
the run signal on.
Connect the relay for emergency stop and for brake in series.
Do not subject the equipment to the place with
rain, waterdrop, poisonous gases or liquids.
Do not carry the servo motor by the cables, shaft
or encoder during transportation.
Do not drop or dump the motor during
transportation and installation.
Store the unit in a place in accordance with the
instruction manual.
If store it for a long time, Consult HCFA.
Please dispose the battery according to your local laws and regulations.
When disposing of the product, handle it as industrial waste.
Do not disassemble and/or repair the equipment
on customer side.
Do not turn on or switch off the main power frequently.
Do not touch the servo drive heat sink, regenerative
resistor, servo motor etc. Their temperatures may be
high while power is on or for some time after power-off.
When the drive become faulty, switch off the
control circuit and main power.
If the servo motor is to be stored for a long time,
switch off the power.
< Warranty period>
The term of warranty for the product is 18 months from the date of manufacture. It' s
●
exceptional to brake motors as they are warranted when acceleration/deceleration
times is not beyond the specified service life.
< Warranty coverage >
This warranty applies only when the condition, method, environment, etc. of use are
●
in compliance with the terms and conditions and instructions that are stated in the
instruction manual and user manual for the Product.
However, even during warranty period, the repair cost will be charged on customer
in the following cases.
1) A failure caused by improper storing or handling, repair and modification.
2) A failure caused by the parts which have dropped down or damaged during transportation
3) A failure caused when the products have been used beyond the product specification
4) A failure caused by external factors such as inevitable accidents, including but not
limited to fire, earthquake, lightning stroke, windstorm disaster, flood, salt damage,
abnormal fluctuation of voltage and other natural disaster.
5) A failure caused by the intrusion of water, oil, metal and other foreign matters.
The warranty coverage is only for the product itself. We assume no responsibilities for
●
any losses of opportunity and/or profit incurred by you due to a failure of the Product.
To prevent electric shock ,
injury or fire.
To prevent electric shock ,
m alfunction or dam age
To prevent electric shock ,
injury or fire.
To prevent injury.
To prevent burns or parts
dam aged.
To prevent fire.
Other safety instructions
To prevent electric shock ,
injury or fire.
To prevent injury, electric
shock , fire, m alfunction
or dam age.
To prevent injury, electric
shock , fire, m alfunction
or dam age.
To prevent electric shock .
CAUTION
Installing and wiring
To prevent fire or
malfunction.
To prevent electric shock
or malfunction.
To prevent electric shock
or fire.
To prevent injury.
To prevent injury or
malfunction.
To prevent injury or
malfunction.
Operation and running
To prevent electric shock,
injury, fault or damage.
To prevent injury.
To prevent injury.
To prevent malfunction.
To prevent malfunction.
To prevent injury or
malfunction.
To prevent injury, electric
shock or fire
To prevent fault.
To prevent injury.
To prevent injury.
To prevent injury or malfunction.
Transportation and storage
To prevent malfunction.
To prevent injury or
malfunction.
To prevent injury or
malfunction.
To prevent malfunction.
To prevent malfunction.
Other safety instructions
Maintenance and inspection
To prevent malfunction.
To prevent malfunction.
To prevent burns or
electric shock.
To prevent fire.
To prevent misoperation
and injury.
About maintenance and inspection