Page 4
Use of other accessories may not ensure compliance with FCC RF exposure guidelines. European Conformity Statement Unitech Electronics co., Ltd herewith declares that the Unitech product is in compliance with the essential requirements and all other provisions of the RED 2014/53/EU directive.
Page 6
Waste electrical and electronic equipment (WEEE) Unitech has set up a policy and process to meet the 2012/19/EU concerning electronic waste disposal. For more detailed information of the electronic waste disposal of the products you have purchased from Unitech directly or via Unitech’s resellers, you shall either...
Laser Information The Unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 60825-1. Class II and Class 2 products are not considered to be hazardous. The Unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations.
It may not be functional anymore. Please only use the original battery from Unitech. Using a third party battery can damage our products. Please note that when such damage occurs, it is not covered by Unitech’s warranty policy.
Unitech product for charging. Please remove the power adapter when the battery is fully recharged. The bundled power adapter that comes with your Unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product.
Worldwide Support Unitech’s professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest Unitech regional service representative. For complete contact information please visit the Web sites listed below: Taipei, Taiwan –...
The warranty period is varied from each country. Please consult with your supplier or Unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user.
Chapter 1 - Overview 1.1 Differentiate RP902/RP902 MFi 1. Gift box Outlook RP902 MFi version will have the MFi mark on the gift box (please refer to the picture below). 2. P/N on the Product Label (in the battery Compartment) RP902 Standard: ...
RP902 User’s Manual EA520 User’s Manual 1.2 Package Please make sure the following contents are in the RP902 gift box. If something is missing or damaged, please contact your Unitech representative. The Package Contents RP902 Terminal Battery (PN#1400-900066G) ...
1.5 Getting Started 1.5.1 Install the Battery 1. Turn RP902 to its rear side, and push the battery lock to the right to unlock the battery. Grab two protrusions on both sides of the battery cover, and lift upward to remove.
1.5.4 Turning on the RP902 for the first time 1. Short press the power/trigger key to power on RP902. 2. Power on RP902 for the first time, the communication LED will show green flash first then “flashing blue light” that indicates RP902 is waiting for Bluetooth connection.
Page 36
Shows the amount of tags being read. *Note: Please note that RP902 does not support continuous reading by single press of trigger key for more than 15 seconds. Users need to release the trigger key and press again to start a new round of reading.
EA520 User’s Manual 2.5 Reading RFID Tags It is recommended to read RFID tags by aiming the antenna area of RP902 at the RFID tag horizontally (as shown in the picture below.) Reading distance may be impacted by the type of tag and environmental conditions.
EA520 User’s Manual 2.9 Connecting to an APPLE iOS Device Note: You can only connect RP902 to an APPLE iOS Device through BLE HID mode. 1. Getting Start → Enter the Setting page by short pressing the Function/Select Up Key → Enter the Operating Mode → Select BLE HID Mode, and RP902 will restart.
RP902 User’s Manual EA520 User’s Manual 2.10 Disconnect Long press (about 3 -5 secs.) the two buttons at the bottom of RP902 at the same time to release the BT connection between the host device and RP902. 2.11 Firmware Update...
Need help?
Do you have a question about the RP902 and is the answer not in the manual?
Questions and answers