Foreword Manual content, use and maintenance Storage of manual of use and maintenance Updating the manual Confidentiality Machine delivery FB45 Technical description Liability limitations Warranty Serial number General safety rules Recommendations Warnings Li-Ion Battery Li-Ion Battery Warnings Li-Ion Battery Recommendations...
Page 3
Battery charger technical data Spare parts Packaging specifications and dimensions Machine unpacking Machine assembly Installing the battery Uninstalling the battery Charging the battery How to get started ON/OFF Battery charge level Functioning Transport After cleaning Maintenance Troubleshooting tips...
The technical information (texts, drawings and illustrations) contained in this manual are the property of Floorwash® S.r.l. and must be considered confidential. It is strictly forbidden to disclose, reproduce or translate this document, even partially, without obtaining prior written permission from Floorwash®.
Floorwash® S.r.l. warrants this product against manufacturing or material defects for a period of two years from the date of purchase. During this period, Floorwash® S.r.l. . at its discretion, shall repair or replace any faulty product at no charge. However, Floorwash® S.r.l. specifies that the warranty is not valid in the following cases: •...
SERIAL NUMBER The label with the serial number is located below the machine, in the underlying part of the ex- ternal left side. That number shall be always notified for technical assistance or request of spare parts. 11111111 GENERAL SAFETY RULES This floor scrubber-dryer is easy to use;...
Warnings Do not use or keep the machine outside in wet conditions, and avoid direct exposure to rain. The machine is suitable for use in dry conditions at a temperature range of +5°C to +35°C (+41°F to +95°F). Do not insert objects through openings. Do not use when openings are clogged.
LI-ION BATTERY Warnings Please read this manual carefully before using and checking the battery and charger. The manufacturer declines any responsibility for damage to property and/or people resulting from the failure to comply with the warnings stated in the manual or the improper use of the battery.
Recommendations • In the event of battery faults (odour emissions, excessive heat generation, deformation, etc.) or malfunctions, immediately remove the battery from the unit or charger and proceed with replacement and disposal. • Only use chargers that are compatible with the technical specifications of the battery to be charged.
TECHINCAL DATA FLOORWASH® FB45 Machine weight 140 mm Machine width 485 mm Machine length 330mm Front brush Ø 88,5 700 Rpm Rear brush Ø 54 114 Rpm Working width 450 mm Working capacity 750 mq/h Brushless motor power Brushless 580 Watt...
PACKAGING SPECIFICATIONS AND DIMENSIONS The FB45 machine is delivered in a protective packaging. Ensure that the packaging is fully intact and that there are no signs of tempering when the product is taken over. In case of damage, the customer shall notify our customer service immediately.
MACHINE ASSEMBLY Follow the procedure below: The FB45 machine has a fast assembly system since no tools are required. Do not use any tool to avoid injuries or damage to the machine. 1 Place the body of the machine on a stable surface without slopes.
INSTALLING THE BATTERY Follow the procedure below: Make sure the battery is off before performing any operations Check the Battery charge level before use. 1 Insert the Battery into its holder. 2 Insert the plug into the socket located on the bottom of the battery holder.
CHARGING THE BATTERY Follow the procedure below: Make sure the battery is off before performing any operations Use only the Charger supplied by the Manufacturer. Any damage or malfunction caused by the use of Chargers other than those supplied by the Manufacturer shall not be covered by the Warranty.
HOW TO GET STARTED The FB45 machine is a mechanical collection device that can achieve excellent results even with the use of water without detergent. An excellent result is achieved with the use of specific detergents. The machine comes with universal brushes (gr 0.12). Anyway, it is possible to request specific brushes to our customer service according to the type of surface to be treated.
ON/OFF Make sure the battery is off before performing any operations Before the start-up of the device, check that the electrical cord and the machine are not malfunctioning in any way. If this is not the case, do not use the device and contact our service centre as soon as possible.
Before starting the shutdown procedure, continue to use the appliance for at least ten seconds without dispensing water in order to complete the drying operation. 5 The machine will switch off automatically when returning the tank to a vertical position (rest position).
FUNCTIONING Check that all steps described above have been completed correctly before using the machine Before starting the washing procedure with the machine, remove any solid residual such as dust lumps, stones, glass, paper etc. from the surface which has to be treated. 1 After the engine has turned on, move the machine back and forth with linear movements.
3 The recovery of the dispensed liquid occurs automatically by means of mechanical collection. The liquid will flow into the waste situated in the lower part of the machine. It is important to empty the waste when the seep liquid reaches the maximum mark printed on the back of the waste, thus avoiding an accidental release of the same.
AFTER CLEANING After cleaning, follow these steps: Before carrying out any operation, check that the electrical cord is unplugged from the outlet. Wear protective gloves when carrying out these operations, in order to avoid direct contact with detergent residues or metal edges. 1 Open the upper cover of the machine by pushing the two lateral hooks up.
4 Unhook and drain the clean water tank 2 from any residual of water and/or detergent. MAINTENANCE A regular maintenance keeps the machine safe and always ready to use. Carry out the following operations: Wear protective gloves when carrying out these operations, in order to avoid direct contact with metal edges or sharp plastic parts.
3 Remove the brushes by pressing the button placed on the left side of the machine. Use a damp cloth to clean the internal sides of the machine while checking that seals are not clogged. In case of prolonged inactivity, carry out at least 1 battery recharge cycle every 3 months. If not used for more than 3 months, make sure the battery is completely discharged and then carry out a complete recharge cycle.
Page 24
Floorwash® S.r.l. Via Camillo Golgi, 15 - 25036 Palazzolo sull’Oglio (BS) Italy tel +39 030. 3372724 customerservice@floorwash.com...