Summary of Contents for Jobsite CT2729
- Page 1 800W IMPACT DRILL CT2729 ORIGINAL MANUAL SAVE THESE INSTRUCTIONS AND PRECAUTIONS. READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE. Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
-
Page 2: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: 800W IMPACT DRILL Model: CT2729 Applicable EC Directives: EC Machinery Directive 2006/42/EC EC Directive of Electromagnetic Compatibility 2014/30/EU... -
Page 3: Specification
1. SPECIFICATION Type CT2729 Operating power 220-240V~ 50 Hz Capacity 800W No load speed 0-3000/min Max. Drill chuck 13mm Max. Drilling Capacity Wood 25mm Concrete 13mm Steel 13mm Sound pressure level(LPA) 96dB(A) Sound pressure level(LWA) 107dB(A) Uncertainty(K) 3bB(A) Vibration Level Impact drill into metal =6.55m/s... -
Page 4: Personal Safety
e) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. f) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. - Page 5 f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed.
-
Page 6: Technical Description
3. TECHNICAL DESCRIPTION 1. Drill Chuck 2. Changeover switch (Drilling / impact drilling) 3. Depth gauge 4. Tightening knob 5. Left/right rotation switch 6. On / Off button 7. Auxiliary handle Detail graphic C (Attachable Handle) (c1) Depth gauge (c2) Depth gauge adjuster (c3) Handle... -
Page 7: Unpacking And Checking
4. UNPACKING AND CHECKING Carefully remove the product from the packaging and examine it for any sign of damage that may have happened during shipping. Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the seller and do not attempt to use the product. - Page 8 5. PREPARING THE IMPCAT DRILL Danger of injury! Danger of burning! Before all adjustments and Drills and chisels become very hot settings: during operation. You can be burned by • Turn the machine off. this. DANGER! • Pull out the power plug. •...
-
Page 9: Operation
OPERATION Protective clothing • If possible, wear designated gloves for protection from splinters and shavings. • While working, wear designated protective goggles. Flying shavings can cause injury. • Wear hearing protection for protection against continuous noise in the work place. •... - Page 10 INSTALLING AND REMOVINGDRILL BITS -Whilst gripping the base of the chuck, use chuck key to open up the chuck jaws . -Place the bit into the chuck as far as it will go. Again, grip the base of the chuck and turn the chuck key clockwise so the jaws take up the grip on the drill bit.
- Page 11 DRILLING WOOD AND PLASTIC To prevent splitting around the drill holes on The reverse side, clamp a piece of scrap timber (A) under the material to be drilled. DRILLING METAL Metals such as mild steel, aluminium and brass may be drilled. - Mark the point to be drilled with a Centre Punch(B) to help the drill bit tip to locate.
-
Page 12: Maintenance And Troubleshooting
7. MAINTENANCE AND TROUBLESHOOTING MAINTENANCE Regular inspection and cleaning reduces the necessity for maintenance operations and will keep your tool in good working condition. The motor must be correctly ventilated during tool operation.Avoid blocking the air inlets and vacuum the ventilation slots regularly. TROUBLESHOOTING Note: Remove the plug from the socket before carrying out adjustment, servicing or maintenance. -
Page 13: Explanation Of Symbols
9. EXPLANATION OF SYMBOLS The following symbols are used in this manual and/or on the machine: WARNING – To Denotes risk of personal reduce the risk of injury or damage to the tool injury, user must read instruction manual” In accordance with Mandatory use of eye essential safety standards protection... -
Page 14: Exploded View
10. EXPLODED VIEW Part no Description Part no Description No.01 Left-threaded screw M*25 No.20 Housing No.02 Chuck No.21 Carbon brush No.03 Output spindle No.22 Upper Brush holder No.04 Steel Ball Ф3 No.23 Roll Spring No.05 Rolling bearing 6001-2Z No.24 Inductor No.06 Snap ring 12 No.25... - Page 15 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in China...
Need help?
Do you have a question about the CT2729 and is the answer not in the manual?
Questions and answers