Do you have a question about the SNOW CAB and is the answer not in the manual?
Questions and answers
Summary of Contents for Original Tractor Cabs SNOW CAB
Page 1
SNOW CAB #1697130 PARTS LIST – ASSEMBLY INSTRUCTIONS ! IMPORTANT ! READ THIS MANUAL CAREFULLY AND KEEP FOR FUTURE REFERENCE ! CAUTION ! REMOVE THE VINYL PANELS FOR TRANSPORT IN AN OPEN TRUCK OR TRAILER ! WARNING ! THIS CAB WILL NOT PROTECT OPERATOR FROM INJURIES CAUSED BY ROLLOVER,...
WARNING This cab is designed to provide foul weather protection only. It does not provide protection from noise, exhaust fumes, chemicals or injury from collision, roll-over or other accidents. 1. Do not operate machine in confined areas without proper ventilation 2.
Page 3
! IMPORTANT ! Install safety decals onto Roll Bar. Install the Exhaust Deflector onto the exhaust pipe. Exhaust Deflector Place the deflector over the exhaust pipe. Turn it up so that it does not interfere with the left front tire when turned to the right with axle pivoted up on the left.
Page 4
Carton Contents: Snow Cab #1697130 Key # Part # Qty. Description 12120 Foot, RH 12139 Foot, LH 12122 Front Panel Cross Bar 12123 Front Panel Frame Leg, RH 12124 Front Panel Frame Leg, LH 12125 Foot Pocket Guard, RH (Longer)
Page 5
Step 1; See Figure 1: Use Figure 1 to identify the steel parts. Figure 1...
Page 6
Step 2; See Figure 2 & 2A: Install Foot RH (1) and Front Panel Leg RH (4). A. Place 5/16” flange locknuts on two 5/16” x 2 1/4” bolts as shown. Insert them into the clamps welded to the Foot and Front Panel Leg. B.
Page 7
Step 3; See Figure 3: Install the right Foot Pocket Guard (6) and the Front Panel Cross Bar (3). A. Place the right Foot Pocket Guard (longer) in position as shown. Attach it to the Foot and front Panel Crossbar Leg with two bolts pointed outward. Add nuts, do not tighten at this time.
Page 8
Step 4; See Figure 4: Install the right (shorter) and left Front Posts (8 & 9) and left Foot Pocket Guard (7). A. Insert a bolt forward through the tab on the right Front Post and then the end of the Front Panel Cross Bar. Add a Locknut, do not tighten at this time.
Page 9
Step 6: See Figure 6: Install right and left ROPS Brackets (12 & 13). FRONT A. Place the right ROPS Bracket over the Roll Bar as shown. Insert a 1/4” x 2 3/4” bolt and add a locknut. Do not tighten at this time. B.
Page 10
Step 9: See Figure 9: Install the Doors for Frame / Door Alignment. A. Follow the instructions in the Door Hardware Package to assemble the Doors. B. Install, close and latch both Doors. C. Tighten all framework bolts at this time. Loosen and then retighten the clamps on the Feet and Front Panel Legs.
Page 11
Step 10: See Figure 10: Install Rear Curtain (17). A. Place a piece of the Edge Trim over the outside edges of the Roll Bar Hinge on each side to protect the rear curtain. B. Lay the rod sewn into the top of the rear curtain over the rear of the top frame. Close ®...
Page 12
Step 11; See Figure 11: Install Front Panel Vinyl (18) A. Place the Front Panel Vinyl over the dash. B. Lay the rod sewn into the top of the Front Panel Vinyl over the Front Panel ® Cross Bar. Close the Velcro flaps around the Front Posts.
Page 13
Step 13; See Figure13: Install the Rearview Mirror Head (28), Upper Bracket (29) and Lower Bracket (30). A. Use the bolt, nut and lock washers on the Mirror Head to fasten the Upper and Lower Brackets to the Mirror. Place the lock washers on the outside of the brackets.
For Replacement Parts and Accessories Contact: Original Tractor Cab Co., Inc. P.O. Box 97 6849 W. Front St. Arlington, IN 46104 Phone 765-663-2214 765-663-2101 Email Sales@originalcab.com Visit us on the web to see our other products. www.originalcab.com Cabs for Lawn Tractors, Garden Tractors, Compact Tractors, Snow Blowers, Utility Vehicles Sunshades for Tractors, Mowers, &...
Need help?
Do you have a question about the SNOW CAB and is the answer not in the manual?
Questions and answers