Panasonic PT-LB78 Specifications
  1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Projector
  5. PT-LB78
  6. Specifications
Panasonic PT-LB78 Specifications

Panasonic PT-LB78 Specifications

Portable lcd projector
Hide thumbs Also See for PT-LB78:
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

P ro d u c t N u m b e r :
P ro d u c t N a m e :
As of March 2009. Specifications subject to change without notice.
S
P
E
C
PT-LB78
LCD Projector
F
I
L
E
< 1 >

Advertisement

Table of Contents
loading

Related Manuals for Panasonic PT-LB78

Summary of Contents for Panasonic PT-LB78

  • Page 1 PT-LB78 P ro d u c t N u m b e r : LCD Projector P ro d u c t N a m e : As of March 2009. Specifications subject to change without notice. < 1 >...

  • Page 2: Specifications

    2 m/6.6´ Moulded plastic (PC+ABS) 368 x 88 x 233 mm (14-1/2˝ x 3-15/32˝ x 9-3/16˝)* Approx. 2.96 kg (6.5 lbs.) 0°– 40°C (32°–104°F) 20%–80% (no condensation) PT-LB78 60 Hz 50 Hz 60 Hz 50 Hz 60 Hz 60 Hz 50 Hz 15.75 kHz;...
  • Page 3 4 Video input VARIABLE AUDIO OUT 5 Audio input for Video/S-Video 6 Audio output COMPUTER AUDIO IN 7 Audio input for COMPUTER 1/2 8 Serial PT-LB78 unit : mm (inch) NOTE: This illustration is not drawn to scale. (7-5/8˝) < 3 >...
  • Page 4 L (m) = (diagonal screen size in inches) x 0.0292 – 0.036 maximum L (m) = (diagonal screen size in inches) x 0.0351 – 0.044 Installable Angle Install the projector at an angle within the range shown below. • Vertical direction The projector may be installed at a vertical angle of ±30°.
  • Page 5 NOTE: Pixel thinning is applied to signals that exceed a dot clock frequency of 110 MHz. The display resolution of this projector is 1,024 x 768 pixels. Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.
  • Page 6 It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then try sending or receiving again. When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next command.

  • Page 7: Control Commands

    1 Do not send PON, POF, or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle. 2 When a command other than OSH is sent while the shutter function is operating, the projector will send an ER401 command in reply and release the shutter function.

  • Page 8: Parameter Format

    <lamp condition> <acctch> <color temp> <date> <time> NOTE: If a wrong command is received, the projector will send an ER401 command to the computer. Command example To set the volume to +30, send the command as shown below. Start Command NOTE: When sending commands without parameters, a colon (:) is not necessary.
  • Page 9 Make sure there is an unobstructed space of 150 mm (5-29/32˝) or more around the projector’s exhaust openings. If the projector is placed in a box or enclosure, ensure the temperature of the air surrounding the projector is between 0°C/32°F and 35°C/95°F. Also make sure the projector’s intake and exhaust openings are not blocked.

Table of Contents