1. Manuals
  2. Brands
  3. Panasonic Manuals
  4. Projector
  5. PT-F300NT
  6. Specifications

Panasonic PT-F300NT Specifications

Panasonic pt-f300nt: user guide
Hide thumbs Also See for PT-F300NT:
Table of Contents

Advertisement

Quick Links

See also: Network Manual
P ro d u c t N u m b e r :
P ro d u c t N a m e :
As of October 2008. Appearance and specifications are subject to change without notice.
S
P
E
C
PT-F300NT
LCD Projector
F
I
L
E
< 1 >

Advertisement

Table of Contents
loading

Related Manuals for Panasonic PT-F300NT

Summary of Contents for Panasonic PT-F300NT

  • Page 1 PT-F300NT P ro d u c t N u m b e r : LCD Projector P ro d u c t N a m e : As of October 2008. Appearance and specifications are subject to change without notice.

  • Page 2: Specifications

    B, R: 0.7 Vp-p, 75 ohms, HD/SYNC, VD: TTL (positive/negative polarity compatible) Y: 1.0 Vp-p (including sync signal), 75 ohms, : 0.7 Vp-p, 75 ohms RCA pin x 1, 1.0 Vp-p, 75 ohms PT-F300NT 60 Hz 50 Hz 60 Hz 50 Hz...
  • Page 3 CD-ROM drive or DVD drive IEEE 802.11b/g compatible (built-in wireless LAN system or external IEEE 802.11b/g LAN card must be installed and running normally.) NOTE: Some IEEE 802.11g/b wireless LAN may not allow connection to the projector. RJ-45 PT-F300NT ®...

  • Page 4: Lcd Projector

    Batteries for remote control (AA battery x 2) Wireless Manager ME 5.5 (CD-ROM) (x 1) Safety wire rope (x 1) Replacement lamp unit: ET-LAF100 Replacement filter unit: ET-ACF100 Ceiling mount bracket for high ceilings: ET-PKF100H Ceiling mount bracket for low ceilings: ET-PKF100S PT-F300NT < 4 >...
  • Page 5 Audio input for S-Video and video Serial input Remote input Audio input for computer 1 Audio input for DVI-D and computer 2 Audio output PT-F300NT unit : mm (inch) NOTE: This illustration is not drawn to scale. (12-1/4˝) (8-3/8˝) < 5 >...

  • Page 6: Standard Setting-Up Positions

    1.91 m 0 – 18.1 m 59.5´ 0 – 2.29 m 0 – PT-F300NT unit : mm (inch) L: Distance to screen H: Height from the edge of screen to center of lens NOTE: Illustrations show the projector installed using optional ceiling bracket.
  • Page 7 Optical axis shift function allows to shift the position of a projected image as shown below. (Width of projected image) 0.27H Installable angle Install the projector at an angle within the range shown below.. • Vertical direction The projector may be installed at a vertical angle of ±30°. As of October 2008 0.27H...
  • Page 8 NOTE: Pixel thinning is applied to signals that exceed a dot clock frequency of 150 MHz. The display resolution of this projector is 1,024 x 768 pixels. If the display resolution indicated in the above data exceeds this resolution, image compression will be used to con- vert the input signal to 1,024 x 768 pixels.
  • Page 9 It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then try sending or receiving again. When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next command.

  • Page 10: Control Commands

    1 Do not send PON, POF, or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle. 2 When a command other than OSH is sent while the shutter function is operating, the projector will send an ER401 command in reply and release the shutter function.

  • Page 11: Parameter Format

    <lamp condition> <acctch> <color temp> <date> <time> NOTE: If a wrong command is received, the projector will send an ER401 command to the computer. Command example To set the volume to +30, send the command as shown below. Start Command NOTE: When sending commands without parameters, a colon (:) is not necessary.

  • Page 12: Notes On Projector Placement And Operation

    Replacing the Filter Unit The projector is equipped with the Auto Cleaning Filter (ACF) function, which automatically winds the air filter to set a new filter element in place according to operating conditions. The filter unit replacement cycle is approximately 10,000 hours.

Table of Contents