Table of Contents
Advertisement
Quick Links
Table of Contents
MCF-LW12TERPM Operating Manual
Important safety information
Read this manual before attempting to install the device! Failure to observe recommendations
included in this manual may be dangerous or cause a violation of the law. The manufacturer
will not be held responsible for any loss or damage resulting from not following the
instructions of this operating manual.
Do not dismantle or modify in any way.
The device is not intended to be used as a reference sensor, and enginko Srl will not be held liable for
any damage which may result from inaccurate readings.
Avoid mechanical stress
Do not use any detergent or alcohol to clean the device.
m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860
Advertisement
Table of Contents
Summary of Contents for M2M MCF-LW12TERPM
- Page 1 The device is not intended to be used as a reference sensor, and enginko Srl will not be held liable for any damage which may result from inaccurate readings. Avoid mechanical stress Do not use any detergent or alcohol to clean the device. m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860...
- Page 2 1. Description The MCF-LW12TERPM is a solar powered sensor that reads temperature, humidity, pressure and PM (PM1, PM2.5, PM10) and sends collected data over the LoRaWAN® network. Ideally suited for a wide range of applications such as weather stations, urban monitoring, air quality, industrial, environmental or farming projects.
-
Page 3: Installation
2.2.1 Pipe mount Mount the sensor on pipe as in picture: 2.2.2 Wall mount Mount the sensor on wall as in picture: m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860... - Page 4 Move the NFC antenna of the mobile (the exact position varies depending on the model of the smartphone) to the sensor antenna, in the area shown in the figure: m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860...
- Page 5 At the first power-on, sensor will take from 1 to 5 minutes to give an effective measure of PM. In case of long period inactivity, if necessary, is possible to shut-off again the sensor to prevent battery consumption, via downlink or with LoRa Tool App: m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860...
-
Page 6: Backup Battery
With this battery the sensor can run for 1 year with the rechargeable battery completely discharged. Battery replacement can be done only by enginko or trained personnel. 2.6 Firmware update Download the latest firmwares available on the smartphone with LoRaTool app: m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860... - Page 7 Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860...
- Page 8 Update the sensor with LoRaTool: m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860...
- Page 9 Value can be between 15 and 65535 minutes (default: 30 minutes). Period interval can be set with App or with downlink command. 3.2 Temperature 3.3 Pressure 3.3.1 Altitude compensation m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860...
- Page 10 ). If “Particles” is set to ON, As default particulate matter is expressed as mass concentration (in μg/m particulate matter is expressed as number concentration (in #/cm m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860...
- Page 11 4 LoRaWAN network The sensor is compliant with LoRaWAN® specification 1.0.2, regional 1.0.2b. m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860...
-
Page 12: Other Settings
LoRa syncword can be setted as “private”(0x12) instead “public” (0x34), butthe NS must be setted accordingly(default: public). Band: select the right LoRaWAN ® band settings accodingly to country requirements. m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860... - Page 13 Please check chapter 2.1 UnConfirmed: set for unconfirmed uplinks (default: confirmed uplink). Single join/day: set for to allow only one join per day (default: multiple join allowed). m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860...
- Page 14 As default passwords are equal to 0. Allowed values range from 0 to 999999999 (only numbers). To change the passwords, set the new values with the LoRa Tool App: m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860...
- Page 15 Once the passwords are setted, to gain access from LoRa Tool to the sensor, open the App: and set the right values before reading from the device: m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860...
-
Page 16: Configuration File
6.1 Multi devices configuration WIth LoRa Tool App is possible to configure many devices in an easy way. m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860... - Page 17 LoRaWEB online tool, where for each sensor it is possible to find documentation, javascript examples for parsing, downlink generator and uplink decoder: (iot.mcf88.cloud/LoRaWeb) m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860...
-
Page 18: Maintenance
Keep the surfaces clean and remove dust from the solar panel with a damp cloth when necessary. Remove gently any debris lodged inside the unit. 10 Ordering code m2m Germany GmbH | Am Kappengraben 18-20 | 61273 Wehrheim | 06081 5873860... -
Page 19: Declaration Of Conformity
MCF-LW12TERPM-US enginko LoRaWAN® outdoor PM and environmental sensor US902-928 MCF-LW12TERPM-AU enginko LoRaWAN® outdoor PM and environmental sensor AU915-928 11 Declaration of conformity Hereby, enginko Srl declares that MCF-LW12TERPM complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. 12 Contacts...