Summary of Contents for Raycer RAY24CBT
- Page 1 ORIGINAL INSTRUCTION PETROL GRASS TRIMMER Model: RAY24CBT INSTRUCTION MANUAL WARNING: Read this manual carefully before use it. BUILDER SAS 32, rue Aristide Bergès - ZI 31270 Cugnaux - France MADE IN PRC 2020...
-
Page 2: Table Of Contents
CONTENTS INTRODUCTION/TECHNICAL DATA………………………...……3 GRAPHIC WARNINGS…………………………………………...….4 SAFETY RULES & PRECAUTIONS……………………………..…6 DESCRIPTION………………………………………………….…….9 ASSEMBLY…………………………………………………..……….10 RULES FOR SAFE OPERATION……………………………………11 CUTTING WITH A NYLON HEAD…………………………………12 FUEL & OIL MIXTURE…………………………………………..….14 PREPARING FOR OPERATIONS. …………………………………. 15 OPERATIONS…………………………………………………………16 MAINTENANCE & CARE………………………………………….. .17 TROUBLE SHOOTING………………………………………………..18 TRANSPORT,HANDLING/EXTENDED STORAGE………………...18 TROUBLESHOOTING GUIDE……………………………………..…21... -
Page 3: Introduction/Technical Data
By the way, due to changes of specifications, all details of your machine may not agree with this manual. Please understand accordingly. TECHNICAL DATA -------------- --------------- Technical Data subject to changed without notice. MODEL RAY24CBT Remote type Direct Drive; flexible shaft Maximum speed of linker shaft 9000/9000 /engine speed(min 3000... -
Page 4: Graphic Warnings
GRAPHIC WARNINGS Because a trimmer is a high-speed, fast cutting power tool, special safety precaution must be observed to reduce the risk of personal injury. Read this manual carefully. Be familiar with the controls and the proper use of the unit. Know how to shut it off, and how to unhook a harnessed unit quickly. - Page 5 Always TURN OFF ENGNINE and make sure the cutting tool has stopped before cleaning, removing or adjusting blade. WARNING! WARNING! WARNING! WARNING! Never modify a trimmer in any way. Improper use of the machine can cause SERIOUS OR FATAL PERSONAL INJURY. WARNING DANGER The engine exhaust form this product contains chemicals to cause...
-
Page 6: Safety Rules & Precautions
SAFETY RULES & PRECAUTIONS Proper safety precautions must be observed. Like all power equipment this unit must be handled carefully. DO NOT EXPOSE YOURSELF OR OTHERS TO DANGER. Follow these general rules. Do not permit others to use this machine unless they are thoroughly responsible and have read, and understand the machine manual and are trained in its operation. - Page 7 at least 15 METER(50 FEET) ● Never leave the machine unattended. ● Do not use this unit for any job other than those for which it is intended as described in this manual. ● Do not overreach. Keep proper footing and balance at all times. Do not run the unit while standing on a ladder or on any other unstable footing location.
- Page 8 ● Before proceeding to adjust or repair the machine, be sure to stop the engine and detach the spark plug. ● When the machine is placed in storage for a long time, drain fuel from the fuel tank and carburetor, clean the parts, move the machine to a safe place and confirm that the engine is cooled down.
-
Page 9: Description
DESCRIPTION SAFETY MANUAL included with unit. Read before operating and keep for future reference to learn proper, safe operating techniques. 1. NYLON CUTTER HEAD Contains replaceable nylon trimming line that advances when the trimmer head is tapped against the ground while the head is turning at normal operating speed. -
Page 10: Assembly
ASSEMBLY INSTRUCTIONS HANDLE ASSEMBLY NOTE: The Delta Handle is attached to the shaft but has been turned under for ease of packing. Loosen adjustment knob and rotate handle to top of shaft handle to top of shaft Position handle 6-1/2 to 8-1/2″from throttle(Fig.1) Tighten adjustment knob securely. -
Page 11: Rules For Safe Operation
RULES FOR SAFE OPERATION WARNING DANGER All models trimmers and brush cutters can throw small stone, metal or small objects as well as the material being cut. Read these “Rules for Safe Operation” with care. Follow the instructions in your operator’s manual. Read the operator’s manual carefully. -
Page 12: Cutting With A Nylon Head
CUTTING WITH A NYLON HEAD For nearly all cutting, it is good to tilt the line head so that contact is made on the part of the circle where the line is moving A W A Y you and the debris shield. See appropriate) This results in the debris being thrown A WAY from you. - Page 13 CUTTING WITH A NYLON HEAD TRIMMING: This is feeding the trimmer carefully into the material you wish to cut. Tilt the head slowly to direct debris away from you. If cutting up to a barrier such as fence, wall or tree, approach from an angle where any debris ricocheting off the barrier will fly away from you, Move the line head slowly until the grass is cut right up the barrier, but do not jam (overfeed) the line into...
-
Page 14: Fuel & Oil Mixture
FUEL & OIL MIXTURE Never fill the fuel tank to the very top. Never add fuel to the tank in a closed non-ventilated area. Do not add fuel to this unit close to an open fire or sparks. Be sure to wipe off spilled fuel before attempting to start engine. Do not attempt to refuel a hot engine. -
Page 15: Preparing For Operations
PREPARING FOR OPERATIONS WHEN MIXING GASOLINE WITH TWO CYCLE ENGINE OIL, USE ONLY GASOLINE WHICH CONTAINS NO ETHANOL OR METHANOL (TYPES OF ALCOHOL). THIS WILL HELP TO A VOID POSSIBLE DAMAGE TO ENGINE FUEL LINES AND OTHER ENGINE PARTS. DO NOT MIX GASOLINE AND OIL DIRECTLY IN THE ENGINE FUEL TANK. -
Page 16: Operations
OPERATIONS ENGINE STARTING AND STOPPING PROCEDURES STARTING COLD ENGINE Move the stop switch to “START” position. 1. Give a gentle push on the primer pump repeatedly (7-10times) until fuel comes into the primer pump. 2. Cold Starts: Pull lever up to close choke. 3. -
Page 17: Maintenance & Care
MAINTENANCE & CARE AIR FILTER Accumulated dust in the air filter will reduce engine efficiency. Increase fuel consumption and allow abrasive particles to pass into the engine. Remove the air filter as often as necessary to maintain in a clean condition. Light surface dust can readily be removed by tapping the filter. -
Page 18: Trouble Shooting
TROUBLE SHOOTING Clean or replace the plug if fouled with heavy oily deposits. Replace the plug if the center electrode is worn rounded at the end. Spark gap 0.6-0.7mm (.023".028") Fastening torque = 145-155kg.cm (125-135in.lb) TRANSPORT, HANDLING The engine should be turned off when the unit is moved between work areas. After the engine has stopped, the muffler is still hot. -
Page 19: Troubleshooting Guide
TROUBLESHOOTING GUIDE 1. FAILURE TO START symptom probable cause remedy fuel these is no fuel in tank Add fuel in tank system fuel filter obstruct Clean fuel filter abnormality spark plug instead fuel spark fuel is too dirty fuel instead fuel normal there is water in fuel system... - Page 20 TROUBLESHOOTING GUIDE 2. LOW OUTPUT symptom probable cause remedy flameout when speedup fuel filter obstruct, clean fuel filter 、 clean fuel road 、 fall short of fuel adjust carburetor the smoke is thin, muffler fouled with oily deposits clean the oily deposits carburetor spout backward compress press is shortage piston...
- Page 21 Warranty We guarantee this product for 2 full years. The warranty period for this item starts on the day of purchase. You can prove the date of purchase by sending us the original receipt. We insure over the entire warranty period: •...
- Page 22 ZI, 32 rue aristide Bergès – 31270 Cugnaux - France Tel : +33 (0)5.34.502.502 Fax : +33 (0)5.34.502.503 declares that the machines: PETROL GRASS TIMMER Model: RAY24CBT Serial No.: from xxxxxxxx xxxxxxxx the people name holding the technical file M r.Olivier Patriarca ：...