Table of Contents
Advertisement
Quick Links
Product: Wireless low energy module
Model: HRM1026B
For OEM integration only – device cannot be sold to general public.
Therefore we will not supply the User's manual, the installation manual is the official for OEM.
FCC ID: VIYHRM1026B
IC: 7305A-HRM1026B
■Operational Information
This module has been tested and found to comply with the limits for a Class B digital device
pursuant to Part15 of FCC rules. This module complies with Part15 subpart C of the FCC
rules. Customers should check Part15 subpart B compliance with their own final products
and conduct certification if needed.
■Caution
Any changes or modifications are not expressly approved by Hosiden responsible for
compliance could void the user's authority to operate the equipment.
■Requirement of Labeling
Please describe the following item on the final product including this module:
Contains Transmitter Module FCC ID: VIYHRM1026B
Contains Transmitter Module IC: 7305A-HRM1026B
■Requirement of User's Manual Statement
"This transmitter must not be co-located or operated in conjunction with any other antenna
or transmitter."
User manual
or
or
Contains FCC ID: VIYHRM1026B
Contains IC: 7305A-HRM1026B
Advertisement
Table of Contents
Summary of Contents for Hosiden HRM1026B
- Page 1 Customers should check Part15 subpart B compliance with their own final products and conduct certification if needed. ■Caution Any changes or modifications are not expressly approved by Hosiden responsible for compliance could void the user’s authority to operate the equipment. ■Requirement of Labeling...
- Page 2 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 3 This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example...
- Page 4 Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 5 This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
- Page 6 Plaque signalétique du produit final Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 7305A-HRM1026B". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which...
- Page 7 Product Specification 1. BLUETOOTH SPECIFICATIONS BT core spec version: version 4.0 Supported profiles: GATT Operation channels: 2402 + 2N MHz (N=0,1,2,…39) Output power level: 4dBm maximum Sensitivity: -70dBm at BER0.1% 2. SHORT RANGE RADIO SPECIFICATIONS (NO BLE MODE) Operation frequency range: 2402MHz - 2480MHz Modulation: GFSK...
Need help?
Do you have a question about the HRM1026B and is the answer not in the manual?
Questions and answers