Page 1
Instruction Manual V1.0 Model: IG7141 Thank you for choosing this IRONGEAR product! At IRONGEAR we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don't hesitate to contact at support@irongearav.com (US/CA)
IMPORTANT SAFETY INFORMATION Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our customer service at support@irongearav.com. CAUTION: Avoid potential personal injuries and property damage! • Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
Page 4
TENSION ADJUSTMENT SHOULD BE DONE ONLY AFTER MOUNT INSTALLATION Do not adjust tension without monitor 1. Ensure monitor has been attached to the mount. 2. Read your monitor box or manual to find out monitor net weight. 3. Ensure the net weight of monitor (including accessories) is between 4.4~26.5 Ibs (2-12 kg) per arm.
Page 5
Tools Needed (Not lncluded) Screwdriver Supplied Parts and Hardware Warning : This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts. lf you require replacement parts, contact our customer service at support@irongearav.com.
Page 6
Supplied Parts and Hardware for Step 2 Arm X2 Extension Arm x2 Locating Ring X2 (F) x1 (F) x1 1/8 in.(3mm) 5/32 in.(4mm) Plastic Sleeve X2 Allen Key Allen Key Supplied Parts and Hardware for Step 3 Bolt (A) Bolt (B-1) Spacer (B-2) M4x12mm (X8) M4x16mm (X8)
Page 7
1. Install the Base A. For Clamp Mounting A-1 For Clamp Mounting Slide the cable clips [06] to pole assembly [05] and secure part [a] to Detach the c-clamp entirely pole assembly [05] Warning: Ensure bolts are secured firmly. 5/32 in. (4mm) Connect part [b] to part [a] according to the thickness of the desktop...
Page 8
Secure the pole assembly to the desktop 1.0-3.1 in. (25-80mm) Warning: Ensure bolts are secured firmly. B. For Grommet Mounting Install the grommet bolt [D] to the bottom of pole assembly [05] Warning: Ensure bolts are secured firmly.
Page 9
Secure the pole assembly to the desktop with grommet Warning: Ensure bolts are secured firmly. 2. Install the Arms ① ② Slide the extension arms [02] to the pole Fasten the locating ring [07] at your assembly [05], and attach the plastic desired height.
Page 10
③ ④ Secure the arms [01] to the extension Attach the arms [01] to the extension arms [02] by tightening the preassembled arms [02] set screw [S] using Allen key [F] 1/8 in. (3mm) Warning: Ensure bolts are secured firmly. Step 3 Attach Monitors to the Arms 3-1 Choose Proper bolts 3-2 Install Monitors to the Arms...
Page 11
4. Adjust Gas Spring Tension Be sure to keep the arm in horizontal position during adjustment. Or else, it would be difficult to adjust the mount or damage the mount. 1. If the monitor can stay at the desired height by itself, no adjustment needed. 2.
5. Rotation Restriction Proper usage directions Non-proper usage directions 6. Tilt Adjustment 13/64 in. (5mm) “+” Clockwise: Tighten “-” Counter-clockwise: Loosen Situation 1: If the monitor can stay at the desired tilt angle by itself, no adjustment needed. Situation 2: If the monitor can not stay at the desired tilt angle by itself, turn the bolt clockwise or counter-clockwise as shown until the monitor can stay at the desired tilt angle by itself.
Page 16
Thank you again choosing this IRONGEAR product! IRONGEAR All of us at do appreciate your product purchase. We hope that you are as happy with your product as we are designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry.