Related Manuals for MISUMI IP-001E
Summary of Contents for MISUMI IP-001E
- Page 1 Page 1 of 29 Device manual of MISUMI Video Server IP-001E MISUMI Video Server Products Series User Manual & Installation Guide Version: 1.0 Date: May 13, 2005...
-
Page 2: Table Of Contents
Page 2 of 29 Device manual of MISUMI Video Server Table of Contents TABLE OF CONTENTS..........................2 MISUMI V ? ....................3 HAT IS IDEO ERVER ..........................3 RODUCT EATURES 2. PHYSICAL CONNECTIONS......................4 3. INSTALLATION..........................4 .....................6 ONNECT IDEO ERVER TO NETWORK ........................6 ONNECT... -
Page 3: What Is Misumi Video Server
1. Product Overview What is MISUMI Video Server? MISUMI Video Server is designed for intranet & internet use. Users can view image or change configurations via built-in web server. The two-layer user-validation prevents any illegal user to monitor or change configuration once user validation is... -
Page 4: Physical Connections
Page 4 of 29 Device manual of MISUMI Video Server 2. Physical Connections Etherent DC 5V Side Panel Connections Front Panel Connections IP-001E 3. Installation Connect Power Supply DC 5V Ensure your power adapter specification matchs your power system (ex 110V or 220V) Connect the adapter to the outlet. - Page 5 Page 5 of 29 Device manual of MISUMI Video Server twork connectivity check Please check your network connectivity before you start install the product. Confirm the link status of your LAN is OK. You may try use the following way to check the network.
-
Page 6: Connect Video Server To Network
Page 6 of 29 Device manual of MISUMI Video Server Connect Video Server to network Connect camera Once the power status is OK.the LED in red located at the rear panel of Video Server should light-up. Connect Video Server to your hub/switch by using a normal RJ45 cable, plug the RJ45 cable into the Ethernet connector locate at the rear panel of the Video Server, another side connect to your hub/switch. -
Page 7: Start Your First Time Network Monitoring
Page 7 of 29 Device manual of MISUMI Video Server Start your first time network monitoring Run the “IPLocator” utility, the newly connected Video Server will be listed in the application window. Please remember its’ IP address. Open an Internet Explorer Window input the following address into the address... -
Page 8: How To Visit The Built-In Web
Page 8 of 29 Device manual of MISUMI Video Server How to visit the built-in web Launch your Internet Explorer (I.E. 6.0 or above) first, then type the Video Server’s url. (i.e. http://192.168.1.100). The user validation is disabled as default, no login is necessary. The user is same as the system administrator(Default : root/pass). -
Page 9: About The User Interface Of Video Server
Page 9 of 29 Device manual of MISUMI Video Server About the User Interface of Video Server The upper window is for company logo display (i.e. This is a generic version. The company logo leaves blank). The left side of the window is the control panel. The right window is for image display. -
Page 10: How To Change The Configurations
Page 10 of 29 Device manual of MISUMI Video Server How to change the configurations The system administrator: root is the one who has the privilege to change system configuration if user validation is enabled. The following window will appear when you click [Options] icon in the control panel (left side of the window). - Page 11 Page 11 of 29 Device manual of MISUMI Video Server [Firmware Upgrade]: Please follow the standard procedure to upgrade firmware. Step 0: Stop all unnecessary running application in your PC. Step 1: Uncheck the [Browse..] and [Upload] motion images in the Motion Detection Setting and reboot the hardware.
-
Page 12: How To Change User Logo
Page 12 of 29 Device manual of MISUMI Video Server How to change User Logo We allow you to use your own logo from version v3.0. User logo will not be erased when you upgrade firmware in the future. The detailed procedures are as follows: Step1: Type http://Video ServerIP/LogoUpload.htm... - Page 13 Page 13 of 29 Device manual of MISUMI Video Server Step 4: Reboot Video Server once ChangeLogo is complete.
- Page 14 Page 14 of 29 Device manual of MISUMI Video Server Step 5: You have to clear the [Temporary Internet files] to take changes effect since there is always some catch in the I.E. Please click [Tools] [Internet Options..] on the top bar.
-
Page 15: How To Disable And Enable User Logo
Page 15 of 29 Device manual of MISUMI Video Server Step 7: Refresh I.E. (Click F5) to take changes effect. You will see you new logo below. How to disable and enable user logo Type: http://Video ServerIP/SetOEM.cgi?LOGO=0 to turn off the user logo http://Video ServerIP/SetOEM.cgi?LOGO=1... -
Page 16: User Management
Page 16 of 29 Device manual of MISUMI Video Server User Management The administrator(root) has the privilege to manage users if User Validation is enabled. Here are the configurations available & field definition. [User]: User validation Yes : Enable user check... -
Page 17: Log
Page 17 of 29 Device manual of MISUMI Video Server The system log will be listed in the window when you click [Log] icon. Operation: The operation which user operates Value: The value to change Client IP: The IP address of client PC... -
Page 18: Network
Page 18 of 29 Device manual of MISUMI Video Server Network Allows administrator(root) to change network setting when you click [Network] icon. IP Setting: Please consult you networking manager for the following values Manual: To set network setting manually. DHCP: To let Video Server get network setting from DHCP server automatically. -
Page 19: Video
Page 19 of 29 Device manual of MISUMI Video Server Video Allows administrator(root) to change Image Setting, Traffic Control or Motion Detection. Image Setting Quality: Image Quality (Low/Normal/Good/Fine/Excellent) Images Size: 160x120/176x144/320x240/352x288/640x480/704x576 Rotation: Nomal/180 degree (Upside down) Advanced: Image preference adjustment... -
Page 20: Event
Page 20 of 29 Device manual of MISUMI Video Server Event This Option contains three major functions: Server Configuration, GPIO Configuration and Event Configuration Server Configuration: User can setup Ftp and Mail services that provides the actions in Event setting. - Page 21 Page 21 of 29 Device manual of MISUMI Video Server GPIO Configuration : Allow user to define types of digital input and their status. See Figure below: DO Configuration: Index: the Index of digital output DO Type: define type of digital input to : [Normal Open] or [Normal Close] DO Status: Disable the DO or Enable it.
- Page 22 Page 22 of 29 Device manual of MISUMI Video Server Event Configuration: User can select Event Index to locate Event (range from 0-2) and also decide to enable or disable this event. Three parts of event setting will be discussed below: [Trigger condition], [Delay time],...
-
Page 23: Product Specifications
Page 23 of 29 Device manual of MISUMI Video Server 4. Product Specifications Models IP-001E: MISUMI Video Server with serial communication support Specifications: Items Specifications Model IP-001E Power Supply DC 5V , 1.2A Consumption ~3 Watts Networking Connectivity 10/100 Ethernet... - Page 24 Page 24 of 29 Device manual of MISUMI Video Server Dimension 60mm(W) x 31mm(H) x 84mm(L) Windows 98/2000/XP IE5.X or above Remote Viewing...
-
Page 25: Appendix
Page 25 of 29 Device manual of MISUMI Video Server 5. Appendix Dictation TCP/IP: Transport Control Protocol/Internet Protocol, the protocol used to transmit data between hosts in Internet, which provides data verification and error protection Web: World Wide Web service is used on Internet widely, It’s provides interactive rich content... - Page 26 Page 26 of 29 Device manual of MISUMI Video Server SMTP: Simple mail transportation protocol, provides Email delivery and relay service Hub: Physical layer network inter-link device, which simply connect ports together and broadcasting the data packet to all the port.
-
Page 27: Use Cgi Command To Setup Gpio And Events
Page 27 of 29 Device manual of MISUMI Video Server Use CGI command to setup GPIO and Events How to configure GPIO Process? How to setup DI type in the device http://ServerIP/SetDIType.cgi? Channel=<1>& Enable=<FALSE | TRUE>& Type=<"NC"|"NO"> Example: Set channel 1 (Input channel) into 'NC' type http://192.168.2.1/SetDIType.cgi? Channel=1&Type=NC&Enable=TRUE... -
Page 28: Scenario: Use Di To Trigger Event And Send Images Through Mail And Ftp
Page 28 of 29 Device manual of MISUMI Video Server Type=<0|1>&Enable_Flag=<FALSE|TRUE>&Action_FTP=<ON|OFF>&Action _MAIL=<ON|OFF>&Action_DO=<ON|OFF>&Action_MSG=<ON|OFF>&Actio n_PRESET=<ON|OFF> Index=0~2 event index from 0 to 2 Input_Type: 0 = Digital Input, 1 = Motion detection Enable_Flag:FALSE|TRUE, TRUE=ENABLE, FALSE=DISABLE Action_FTP=<ON|OFF> Action_MAIL=<ON|OFF> Action_DO=<ON|OFF> Action_MSG=<ON|OFF> Action_PRESET=<ON|OFF> Input_index=<Value> Output_index=<Value> Reset=<FALSE|TRUE>... -
Page 29: Turn On Ftp And Email
Page 29 of 29 Device manual of MISUMI Video Server Turn On FTP and Email Setup Event status http://192.168.2.1/SetEvent.cgi? Index=0&Input_Type=0&Enable_Flag=TRUE&Action_FTP=ON&Action_MAIL=ON Check DI type status http://ServerIP/GetDIType.cgi Channel = 1 Enable = 1 Type = NO Check Event Status http://192.168.2.38/GetEvent.cgi Index =0, Input_Type=DI, Enable_Flag=1, Action_Type=...
Need help?
Do you have a question about the IP-001E and is the answer not in the manual?
Questions and answers