Subscribe to Our Youtube Channel
Summary of Contents for quadient PF-60
- Page 1 PF 60 Touchscreen Document Folder (Serial # J182046 and Later) OPERATOR MANUAL FIRST EDITION 5/2020...
-
Page 3: Table Of Contents
TABLE OF CONTENTS SUBJECT PAGE DESCRIPTION SPECIFICATIONS UNPACKING SETUP CONTROL PANEL OPERATION SETTING CUSTOM FOLDS AUTOBATCH MODE MULTI-SHEET FEEDING (OPTIONAL) CROSS FOLDING STACKER WHEEL POSITIONING CHART STACKER WHEEL SETUP FOR THICK PAPER REMOVING OUTFEED COVER REMOVING INFEED TIRES OPERATOR MAINTENANCE ERROR SCREENS TROUBLE-SHOOTING... -
Page 5: Description
DESCRIPTION Non-Operator Side Control Panel Upper Fold Table Self Centering Paper Side Guides Infeed Tray Infeed Tray Extension Telescoping Outfeed Stacker Infeed Tray Lever Lower Fold Operator Side Table Power Inlet & Circuit breaker Power Switch FUNCTION This document folder is designed to perform a wide variety of folds using a variety of paper weights. The fold plates are manually adjusted for standard folds and custom folds. -
Page 6: Unpacking
UNPACKING & SETUP Check package for shipping damage. If there is shipping damage, do not discard the box. Remove the machine and packed components from the box. The fold plates, telescoping stacker, Optional Multi Sheet Feeder if ordered, power cord and cross-fold guide are wrapped separately in the box. NOTE: Two people must lift the machine from the box. -
Page 7: Control Panel
4. If equipped, insert the optional Multi-Sheet Feeder into the four slots located on the top cover (Fig 3). Note: Technical assistance is required to install the multi- sheet feeder components if it is purchased separetly from the folder. 5. Make sure the power switch is in the “OFF” position. Plug the power cord into the power inlet and the wall Fig. -
Page 8: Operation
OPERATION Place power switch in the “ON” position. To set the fold plate stop position, squeeze the stop plate lever and move the stop plate to the desired location on the upper and lower fold plates (Fig 4). Align the pointed part of the stop plate with the desired marks on the decal and release the lever. -
Page 9: Setting Custom Folds
SETTING CUSTOM FOLDS Example 1: Uneven “Z” Panel A Measure the length of panel “A” Adjust the upper fold plate so that the stop plate lines up with the measurements of the panel “A” i.e. if panel “A” is 5 1/4” long slide the stop plate up or down so that Panel B it lines up with the 5 1/4”... -
Page 10: Multi-Sheet Feeding (Optional)
MULTI-SHEET FEEDING (OPTIONAL) The multi-sheet feeder is designed to fold pre-collated stapled or unstapled sets of up to four 20 # (75gsm) sheets of paper. NOTE: This feature will not work in AutoBatch mode. The home screen must be displayed in order for the multi- sheet feeder to work properly. -
Page 11: Cross Folding
CROSS FOLDING Fold Crease Cross Fold Guide Cross folding refers to folding a document in one direction, then running it through the folder a second time to be folded again. Common Application: Folding a 11” x 17” document in half, then letter folding it to fit in a standard #10 envelope. -
Page 12: Stacker Wheel Setup For Thick Paper
STACKER WHEEL SETUP FOR THICK PAPER Thicker paper from 28 # up to 65 # may require special stacker Position 1 wheel setup, moving the stacker wheels closer than the position “A” slot. If stacking is inconsistent, move the stacker wheels from the standard position #1 (Fig. -
Page 13: Removing Infeed Tires
REMOVING INFEED TIRES The infeed tires can easily be removed for cleaning and replacement. Remove the Allen screw located on the left side of the feed tire shaft (Fig. 14a). Slide the shaft to the right to release from the side frame and remove (Fig. 14b). -
Page 14: Error Screens
ERROR SCREENS Paper Mis-Feed / Paper Jam FD 342 Touch Screen -Error Screens Paper Jam Paper misfeed A mis-feed has occurred. Reset the stack of paper in the in-feed and press the “ “ icon to resume op- eration. A Paper jam has occurred in one of the areas Error screen will appear with arrow pointing to infeed. -
Page 15: Trouble-Shooting
TROUBLE-SHOOTING TROUBLE POSSIBLE CAUSE REMEDY Control panel is not No power at the wall outlet. Check wall outlet. illuminated. No power to the machine inlet. Check power cord for frayed/broken wires. No power to the control panel. Press the button on the circuit breaker. Internal electrical failure Call for service “Cover Open”...
Need help?
Do you have a question about the PF-60 and is the answer not in the manual?
Questions and answers