Global Sources SD-X0608T Owner's Manual

Metal garden shed

Hide thumbs

page of 30

/ 30
Bookmarks

Quick Links

Download this manual

Metal Garden Shed

OWNER'S MANUAL

Instructions for Assembly

Requires two people and takes 2-3 hours for lnstallation.

Quick & Easy Assembly

Ridge Reinforced Walls

-1-

SD-X0608T

Need help?

Do you have a question about the SD-X0608T and is the answer not in the manual?

Questions and answers

Summary of Contents for Global Sources SD-X0608T

Page 1 Metal Garden Shed OWNER'S MANUAL OWNER'S MANUAL Instructions for Assembly Instructions for Assembly SD-X0608T Requires two people and takes 2-3 hours for lnstallation. Requires two people and takes 2-3 hours for lnstallation. Quick & Easy Assembly Quick & Easy Assembly...
Page 2 BEFORE YOU START PLAN AHEAD Site Selection Owner's Manual Avoid overhanging trees as much as possible as leaves will make regular cleaning Prior to installation, it is important that you contact your local government authority to necessary and broken branches are a potential hazard. determine if building approval is required.
Page 3 Qty. Qty. Qty. Qty. PART PART PART PART 1118mm 955mm 356mm 955mm 959mm 1118mm 24-1 660mm 1169mm 959mm 15-1 24-2 1169mm 1304mm 660mm 15-2 139mm 702mm 1304mm 702mm 139mm 1029mm 16-1 1720mm 1029mm 286mm 1720mm 1179mm 286mm 1032mm 548mm 1304mm 1090mm 1105mm 662mm...
Page 4 Qty. Qty. Qty. Qty. Qty. PART PART PART PART PART 1720mm 1720mm 1720mm 1710X552mm 1720mm 1207mm 1207mm 1207mm 1710X552mm...
Page 5 -5- -5-...
Page 6 F1x 24 2L x 1 1L x 2 1R x 2 2R x 1 3L x 1 3Rx 1 5 x 1 Two holes need to fit together, if not pls turn 1L 1R 2L 2R around and try again. Ⅱ...
Page 7 、 When diagonal measurements are equal,the frame is square. 、 The Floor Frame must be BOTH square AND level or the holes will not line up properly.
Page 8 P1 x 1 P4 x 1 F2 x 1 F1x 9 S3 x 10 Ⅰ Ⅰ Ⅱ Wall panels ALWAYS attach to the Floor Frames with Screws in the manner shown above .Rest the Panel on the Floor Frame and Ⅱ...
Page 9 S3 x 5 F1x 5 22R x 1...
Page 10 P2 x 1 P4 x 1 F1x 9 S3 x 9 Ⅰ Ⅰ Ⅱ Ⅱ -10-...
Page 11 F1x 12 S3 x 10 22Lx 1 23R x 1...
Page 12 P4 x 1 P3 x 1 22Rx 1 23L x 1 F1x 24 S3 x 22 Ⅰ Ⅱ Ⅰ Ⅰ Ⅱ Ⅱ Ⅲ Ⅳ...
Page 13 P4 x 1 P1 x 1 22L x 1 F1x 15 F2 x 1 S3 x 15 Ⅰ Ⅰ Ⅰ Ⅱ Ⅱ Ⅱ Ⅲ...
Page 14 P3 x 3 P2 x 1 F1x 50 S3 x 50 -14-...
Page 15 9 x 2 11 x 2 F1x 36 S3 x 3 Assembly No. 11, then No. 9 one by one.and secure them with (F1) screws from inside as shown. -15-...
Page 16 GF x 4 21R x 2 B3 x 2 B4 x 2 12 x 2 S3 x 20 21L x 2 B1 x 2 B2 x 2 F2x 20 -16-...
Page 17 F1x 22 S3 x 20 10L x 1 10R x 1 Assembly No. 10L, then No. 10R one by one. -17-...
Page 18 F1x 8 S3 x 7 x 1 8 x 1 G2 x 4 Notice the hole on it -18-...
Page 19 F2x 2 16 x 1 16-1x 1 Two holes need to fit together, if not pls turn 16 16-1 around and try again. 16-1 16-1 -19-...
Page 20 13 x 2 14 x 2 F2x 8 Ⅱ Ⅲ -20-...
Page 21 F2x 2 16 x 1 16-1x 1 16-1 -21-...
Page 22 13 x 2 14 x 2 F2x 8 F1x 4 Ⅲ Ⅲ Ⅱ Ⅱ Ⅲ Ⅲ Ⅱ Ⅲ Ⅲ -22-...
Page 23 4Lx 1 4R x 1 6 x 1 F2x 2 F1x 10 S3 x 12 -23-...
Page 24 P5 x 1 P6 x 1 F1x 24 S3 x 24 -24-...
Page 25 P8 x 2 F1x 24 S3 x 24 -25-...
Page 26 P5 x 1 P6 x 1 F1x 24 S3 x 24 -26-...
Page 27 S3 x 6 17 x 4 19 x 1 20 x 1 GE x 2 F1x 9 -27-...
Page 28 15-1 x 1 15-2 x 1 24-1 x 1 24-2 x 1 GC x 4 GS x 4 F1 x 24 S3 x 22 15-1&15-2 24-2 24-1 24-1 24-1 15-1 15-1 24-1&24-2 24-2 15-2 -28-...
Page 29 D1x 1 D2x 1 18 x 6 GB x 2 GDx 4 F1x 12 F2x 22 S3 x 34 D1&D2 -29-...
Page 30 F3x 8 7&8 -30-...