Advertisement
TROUBLESHOOTING
a. The thermal circuit
1. The water level is too low
breaker cuts in as the
2. Intake blocked, impeller jammed.
motor has overheated.
3. Temperature of inlet water exceeds 35
b. Motor operates but
4. Water level below min suction depth.
there is no suction.
5. Air bubbles in pump accumulated during submersion, or because float is incorrectly
positioned so pump does not stop at min level and sucks in air.
6. Clogged intake filter or discharge pipe
c. Reduced water volume
7. Discharge pipe bent, or pinched.
for level of water
8. Discharge pipe too narrow.
9. Pump partially blocked.
10. No electrical power.
d. The pump will not start
11. Float not working
or suddenly stops
12. Circuit breaker has triggered.
during operation.
13. Impeller is jammed.
Declaration of Conformity
SUBMERSIBLE WATER PUMP
Models: SWP20, SWP20A.
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
BSEN 60335-2-41
Model SWP20
Item Part No
Description
1
EL20004
BEARING
2
EL20007
OIL SEAL
3
EL10016
IMPELLER
4
EL10019
SUBMERSIBLE PUMP BODY
5
EL20024
CAPACITOR
6
EL10040
H 07 RNF CABLE SCHUKO PLUG
7
EL20061
ASPIRATION BASE
8
EL5001C
COMPLETE MOTOR
9
EL2014C
OR SEAL 129,40x1,78
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required
for any claim. INFORMATION: Call us for a copy of our latest catalogue and promotions on 01284 757525 and leave your full name and address including postcode.
01284 757500
C
O
We, the sole importer into the UK, declare that the products listed below are in conformity with the following EEC standards and directives
The construction file for these products are held by the Manufacturer and may be inspected, by a national authority,
upon request to Jack Sealey Ltd.
Signed by Mark Sweetman
I N S T R U C T I O N S F O R :
Sole UK Distributor,
Sealey Group, Bury St. Edmunds, Suffolk.
01284 703534
1. Sink the pump deeper, or allow to cool before continuing use.
2. Check and clean.
3. Reduce water temperature. Allow the circuit breaker to cool for approx 25mins before restarting.
4. Stop the pump.
5. Release air by inclining the pump and re-immersing it in water.
6. Remove dirt, and clean the unit.
7. Straighten pipe
8. Use wider diameter pipe.
9. Clean pump.
10. Check cable, plug and fuse.
11. Contact authorised service agent.
12. See (a) above.
13. Clean the pump.
7th August 2000
MODELS: SWP20, SWP20A
Model SWP20A
Item Part No
1
EL20004
2
EL20007
3
EL10016
4
EL10019
5
EL20024
6
EL10039
7
EL10040
8
EL10061
9
EL1001C
10 EL2014C
sales@sealey.co.uk
e-mail
For Jack Sealey Ltd.
Sole importer into the UK
of Sealey Power Products.
WAT E R P U M P
Original Date:
Issue Date:
Version No:
Date Modified:
Description
BEARING
OIL SEAL
IMPELLER
SUBMERSIBLE PUMP BODY
CAPACITOR
FLOAT SWITCH
H 07 RNF CABLE SCHUKO PLUG
ASPIRATION BASE
MOTOR
OR SEAL 129,40x1,78
www.sealey.co.uk
9A>
Advertisement
