Subscribe to Our Youtube Channel
Related Manuals for INNOVATIVE CIRCUIT TECHNOLOGY HELIOS ICT DIN Series
Summary of Contents for INNOVATIVE CIRCUIT TECHNOLOGY HELIOS ICT DIN Series
- Page 1 Innovative Circuit Technology Ltd. ICT DIN SERIES POWER SUPPLY INSTRUCTION MANUAL 855-361-000 Models: ICT360-24DIN ICT360-48DIN...
- Page 2 Rev. 0.0 (2023) Copyright © 2023 Innovative Circuit Technology Ltd. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of Innovative Circuit Technology Ltd.
-
Page 3: Table Of Contents
Table of Contents PRODUCT DESCRIPTION ................4 INSTALLATION ..................... 6 WIRING ......................7 OPERATION....................9 Status Indicators and Alarms……………………………………………………………..10 PRODUCT SPECIFICATIONS ................ 11 Innovative Circuit Technology Ltd. -
Page 4: Product Description
2. Form C / Temperature sensor connector 3. RJ11 serial port for communication with ICT DIN Power Distribution Unit 4. Selector dial for battery charging current 5. Status LEDs 6. AC input terminal Figure 1. Front view of ICT DIN Power supply Innovative Circuit Technology Ltd. - Page 5 AC input wiring to the ICT DIN Power Supply must be protected using an outlet with a branch rated circuit breaker of 20A or lower value. Figure 2. - 48V system Connection Diagram of ICT DIN Series (POS Ground System) Innovative Circuit Technology Ltd.
-
Page 6: Installation
RJ-11 COMM ports together using the data cable, as shown in Figure 2. The green “DC OK” LED will blink once every 10 seconds if the data connection is functioning properly. Innovative Circuit Technology Ltd. -
Page 7: Wiring
LOAD connection to minimize the voltage drop due to cable length in cases where load cable is more than 15 feet from the unit. For the battery connection, utilize single wiring. Refer to the following table for the appropriate wire gauge (AWG). Innovative Circuit Technology Ltd. - Page 8 TEMP inputs on the connector (polarity does not matter). Affix the probe body to a side midpoint on one of the battery cases using the adhesive backed plastic clip included with the sensor. Innovative Circuit Technology Ltd.
-
Page 9: Operation
Combined with the ICT DIN Power Distribution Unit, remote monitoring is available through the Ethernet controller and user interface showing in figure 4. Figure 4. GUI with Power Supply and Battery status Innovative Circuit Technology Ltd. -
Page 10: Status Indicators And Alarms
10 sec. Clears when Battery PDU) Current drops 0.5A below Overcurrent threshold for 10 sec. The Form-C alarm contact will be triggered for any condition that lights the red FAULT LED or shuts down the output of the unit. Innovative Circuit Technology Ltd. -
Page 11: Product Specifications
5 pin connector Operating Temperature Range: -30°C to +60°C Storage Temperature Range: -40°C to +70°C Humidity: (Operating) 10 – 90% (non-condensing) (Storage) 5 – 95% (non-condensing) Cooling: Convection cooled De-rate output 2% per °C above 40°C Innovative Circuit Technology Ltd. - Page 12 Regulatory Compliance (Safety): Designed to meet UL/CSA62368 Regulatory Compliance (EMC): Designed to meet FCC Part 15 Class B limits Dimensions (inches): Weight : 1.65kg/3.6lbs Innovative Circuit Technology Ltd.
- Page 13 Figure 5. De-rating Curve of Output Power VS Temperature Innovative Circuit Technology Ltd.
- Page 14 ICT and Purchaser with respect to the subject matter herein and supersedes all prior verbal or written communications, representations, understandings or agreements relating to this subject. INNOVATIVE CIRCUIT TECHNOLOGY LTD. 26921 Gloucester Way Langley, British Columbia, Canada V4W 3Y3 T 604.856.6303 F 604.856.6365...
Need help?
Do you have a question about the HELIOS ICT DIN Series and is the answer not in the manual?
Questions and answers