Table of Contents
Advertisement
(5) Open angle of the two tab of 6 pole magnet by isogonic
angle and accord with vertical line of Red/Blue and Green.
(6) Maintain as angle of (5) and rotate the tab to accord with
horizontal line. In case of twisted horizontal line,repeat
adjustment of (3) ~ (5) remembering the movement of
Red/Green/Blue color.
(7) Move the DY to best condition of convergence and attach
the CPT to a rubber-chock for fixing DY.
5. Screen voltage adjustment
(1) Receive the PAL or SECAM(NTSC) signal into RF mode
(regardless of channel).
(2) If you press the "ADJ"button in LINE SVC mode(IN-START
button),the LINE SVC mode changes to screen adjustment
mode.
(3) Turn the Screen Volume of FBT to change luminance of
White signal center as shown below.
(4) Press the TV/AV button to exit SVC mode.
6. White balance adjustment
NOTE : When adjusting white balance automatically,connect the
adjustment JIG in SVC mode.(When pressing IN-
START,MUTE button on remote control for adjustment
orderly,it is changed to CPU OFF mode and screen is
displayed to "CPU OFF".)
(1) Receive 100% white pattern.
(2) Adjust LOW Light status(4.5FL) of CR(R CUT), CB(B CUT)
at CG(G CUT:75) : 60.
(3) Adjust HIGH Light status(35FL) of WR(R DRIVE), WB(B
DRIVE) at WG(G DRIVE:380) : 450.
(4) Repeat above step (2) and (3) for the best condition each
status of High Light and Low Light.
<Table 1> White Balance Color analyzer
Menu
X
Y
Color Temperature
9000
<Table 2> White Balance Initial Data
Menu
LOW LIGHT
CR
CG
CB
HIGH LIGHT
WR
WG
WB
<Table 3> White Balance Initial Data
1. IC
Name
Maker
VCD IC
VCT49xyi
Micronas
EP_ROM
24C16
ST, ATMEL
All manuals and user guides at all-guides.com
EU
N-EU
288
268
295
273
K
13000
K
o
o
Range
DATA
0 ~ 511
60
0 ~ 511
60
0 ~ 511
60
0 ~ 511
450
0 ~ 511
450
0 ~ 511
450
Algorithm
0
B
0
0
2. White balance IIC Parameter
Program
TWBeng_v049(hex)
Vcd Slave
BCF0
R_Amp
Program
TWBeng_v049
Sub Add
1C8
Start Bit
C
Stop Bit
4
Offset
0
Polarity
1
EP_Rom_S
9091
Speed/ Plus
0.5
<Note>
- W/B Program "Twbeng_v049" Only
How to use to Remote control key.
1. After Cutoff adjustment then W/B adjustment
: Instart -> adj. -> mute(cutoff)-> tv/av(wb)
All clear key is EXIT key
2. W/B adjustment only
: Instart -> mute(cpuoff) ->
All clear key is TV/AV key
7. Deflection setting Data Adjustment
7.1 Adjustment preparation
(1) Tune the TV set to receive an Digital pattern(EU05CH).
(2) Deflection setting data adjustment is operate by SVC
communicator.
(3) Enter the deflection mode by selection SERVICE2 key on
SERVICE MENU after enter the adjustment mode by
pressing LINE SVC MODE(IN-START KEY).
(4) Use the CH D ,E key to select adjustment item.
(5) Use the VOL F ,G key to increase/decrease data.
7.2 Adjustment
<Note>
- When adjusting a deflection,adjust N50Hz of PAL signal first and
adjust a deflection data at N60Hz(NTSC), Z60Hz, N50Hz,
W50Hz, Z50Hz.
- After finishing deflection adjustment, press the ENTER
button to enter or exit SVC mode.
(1) VL(Vertical Linearity) adjustment
Adjust the top & bottom size of inner circle to be equal.
(2) VA (Vertical Amplitude) adjustment
Adjust so that the circle of a digital circle pattern should be
located interval of 6~7mm from the effective screen of the
CPT.
(3) SC (Vertical S correction) adjustment
Adjust so that all distance between each lattice width of
top/center/bottom are to be the same.
(4) VS (Vertical Shift) adjustment
Adjust so that the geometric vertical center line is in accord
with vertical center line of CPT.
(5) HS(Horizontal Shift) adjustment
Adjust so that the geometric horizontal center line is in
accord with horizontal center line of CPT.
- 9 -
Program
TWBeng_v049(hex)
Speed
Eprom_Slave
AC
R_Cut
B_Amp
TWBeng_v049
TWBeng_v049
TWBeng_v049
1C3
1CA
C
C
4
4
0
0
1
1
8A8B
9495
3
0.5
Delay
1
30
B_Cut
1C5
C
4
0
1
8E8F
3
Advertisement
Table of Contents
