Klima 4251 Assembly Instructions

We start building the model by reading the instructions and the construction plan (drawing) included in the
The package includes a set of structural elements and accessories that allow you to build and launch your own
If you want to use the model only for rubber launchers, your age should not be under 14.
However, if you plan to use the model to take off with the TSP L-2HP model rocket engine, you should be at least
18 years of age or under the supervision of a person over 18 years of age. Additionally, you must read the
instructions for use and safety that come with the package with the TSP motors.
The package of the jet model kit should contain the following structural components for the model:
Once you have checked if all the above-mentioned items are included in the set, you can start building the
1. Glue the turret for the fins (3) to the fuselage (1), do it in the place of the fuselage marked on the plan, remember to
2. Then, start assembling the wing panel - set the rise on every of the wing ends (5) about 10-12mm, then glue the rise
in the middle of the wing with glue. Then insert the wing flap into the oblong mounting hole (notch) in the fuselage,
before sticking the wing to the fuselage, make sure that the rise on the left and right tips of the wing is equal to the
fuselage, then, looking from the top of the model, make sure that the wing is at a 90-degree angle relative to the hull.
3. Glue the horizontal / height stabilizer (4) in exactly the same way as the wings into the assembly place cut in the
stabilizer turret, previously glued to the fuselage. However, in this case, the rise at the ends of the fin is not necessary -
be careful to stick it at a 90 degree angle to the fuselage, also looking from the top of the model.
4. Then stick the directional / vertical fin (2), do it by sticking it on the fin turret in the place marked on the plan,
5. We proceed to stick the fuselage claddings (9), they should be glued to the front of the fuselage, in the place indicated
on the plan, it is best to help yourself in this with carpentry clamps (crocodile clips).
6. Install the starting hook (8) in the place indicated on the plan. However, first cut the bamboo stick in half. Then
hammer the hook with the sharp end in the center of the hull axis, in the manner and place indicated on the plan, while
taking care that the sharp end of the hook does not pierce the hull from any side. Finish the operation by gluing the
7. OPTIONALLY, stick the hopper (7) on the TSP L-2HP engine, for this purpose put the hopper turret with the
mounting cutout on the hull in the place marked on the plan. Set the right angle of the turret in relation to the axis of the
carrier blade - the exact angle can be found on the model construction plan.
8. OPTIONALLY, tape the model's hull behind the engine compartment with self-adhesive aluminum tape (8) in order
to protect the fuselage from hot gases coming from the TSP L-2HP engine nozzle.
9. Finally, you can add authenticity to your model by decorating it with the graphics and paints with a brush included in
the set. Paint the edges of the laser cut with the appropriate color (remember that the paint included in the package is
acrylic, so you can wash it off with water before it dries), then stick the graphics / stickers in the places marked on the
Your model is almost ready for its first flight. Before flying, you need to properly balance your model, to do this check
the center of gravity (CG) - to do this, support the model with two fingers (thumb and forefinger of one hand) under the
wings in the place marked on the map as the center of gravity (CG). When properly balanced, the front of the model
should be slightly tilted downwards. If the model tilts on the tail, stick the piece of balance (plasticine) included in the
kit to the front of the model. If it is the opposite, stick a piece of balance to the rear end of the fuselage (tail).

Assembly instructions for the SPARK (ISKRA) FIGHTER JET

jet plane model.
1. 3mm-4mm balsa hull - 1 piece
2. 1mm balsa vertical stabilizer (direction) - 1 piece
3. 3mm turret for vertical stabilizer
4. 1.5mm balsa horizontal (height) stabilizer - 1 piece
5. 1.5mm balsa wing - 1 piece
6. Container for the TSP L-2HP engine - 1 piece
7. Self-adhesive aluminum foil - 1 piece
8. Starting hook - bamboo fi 2mm - 1 piece
9. Hull cladding
And additional components:
- Stickers with jet markings / graphics - 1 set
- SuperGlue glue - 1 piece
- Balance (plasticine) - 1 piece
- Sandpaper - 1 piece
- Modeling rubber 1x3x500mm - 1 piece
place it in line with the fuselage axis.
Now you can stick the wing to the fuselage.
remember to position it exactly in the fuselage axis.
hook using the glue included in the set.
set.
- Paint kit
model:
plan.