Advertisement
Quick Links
Photos show end panel examples. Lower photo shows an installed panel as seen from the inside.
©2008 ClearSpan™
All Rights Reserved. Reproduction
is prohibited without permission.
Revision date: 04.10.08
ClearSpan
End Panel
™
Installation Guide
CLEARSPAN
END PANEL INSTALLATION
™
STK#
107909
End Panel Installation Guide
Advertisement
Related Manuals for ClearSpan End Panel
Summary of Contents for ClearSpan End Panel
- Page 1 END PANEL INSTALLATION ™ ClearSpan End Panel ™ Installation Guide Photos show end panel examples. Lower photo shows an installed panel as seen from the inside. ©2008 ClearSpan™ STK# All Rights Reserved. Reproduction 107909 End Panel Installation Guide is prohibited without permission.
-
Page 2: Assembly Procedure
ATTENTION: The frame and end panels shown throughout READ THIS DOCUMENT BEFORE YOU BEGIN! this guide may differ from your frame and end panel. It is the responsibility of the owner/installer to adapt these steps Thank you for purchasing this ClearSpan™ end panel as needed to attach the actual end panel. - Page 3 Consult Panel A and Panel B on Page 5 to view typical end panel designs. The procedures presented in this guide describe attaching a typical end panel to a typical end frame of a ClearSpan™ • End panels that are 30' wide or wider typically include building.
- Page 4 CLEARSPAN END PANEL INSTALLATION ™ The parts shown below are contained in a typical end panel ATTENTION: Installation kits for end panels with D-rings installation kit. The width and height of the end wall and the attached to the upper edge also include the parts shown in this end panel design determines the components of the typical column.
- Page 5 Tek screws and washers. Consult the services of a professional contractor to determine the best way to secure your end panel to the end frame. May not apply to custom end panels or to your end frame. Panels of this design are typically attached to the end rafter using fabric clips and Tek screws.
- Page 6 The panel skirt can remain loose or it can be secured to the end wall as desired. For typical applications, the upper flap of the end panel is pulled between the end rafter and the main cover. It is then secured to the end rafter using a few Tek screws and washers to keep it in place.
- Page 7 Tek screws. (without D-rings) to an end rafter and end frame. Some steps may not apply to your (or a custom) end panel. NOTE: These fasteners temporarily hold the end panel in place while securing the lower edge to the base rail.
- Page 8 Tighten the end ratchets to secure the bonnet of the main cover. After the end panel is fully stretched and all doors are installed (if equipped), reattach the end ratchets for the Move to the other end of the building and secure the main cover bonnet.
- Page 9 END PANEL INSTALLATION (D-Rings) With the temporary straps (or customer-supplied rope) in place, pull the end panel up to the end rafter and The following procedure describes installing an end panel secure the end panel to the end rafter using small that includes D-rings at the top (Panel C on Page 6) and sections of the strap.
- Page 10 1" strap at the top of the end panel. NOTE: For a typical end panel, the upper edge is pulled tightly up to the rafter. Verify that the lower end of the panel remains on the ground as the top is tightened. If the panel begins to lift off the ground, loosen the top evenly along the radius of the rafter.
- Page 11 ATTENTION: This metal pipe is inserted into the horizontal Inside View pocket on the inside surface of the end panel. If doors are to be installed, cut the pipe to the correct length to properly WARNING: Cut only the end panel pocket. DO NOT fit into the pocket and to remove it from the opening.
- Page 12 After all the conduit straps are tight, move to the top of and work up the conduit and pocket. the end rafter and tuck the end panel flap over the top of the end rafter. The end panel flap is tucked between Top of the End Panel the end rafter and the main cover.
- Page 13 ATTENTION: For best results and to keep the stretched panel in position, install Tek screws and washers from the outside around the door frame to secure the end panel to the door jambs and header. (See dashed lines Fig. 1.) Do this before cutting the opening in the panel.
- Page 14 NOTE: The arrows in the above diagrams (base rail) show where to reattach the end ratchets to secure the bonnet of the main cover. The ratchets are typically reattached through the end panel and to the end wall base rail. Pull the main cover bonnet back over the end rafter and use the bonnet straps as a guide to properly position each ratchet.
- Page 15 CLEARSPAN END PANEL INSTALLATION ™ SHELTER CARE AND MAINTENANCE Proper care and maintenance of your ClearSpan™ shelter Space below is reserved for customer notes. and its components is important. Check the following items periodically to properly and adequately maintain your building: •...
Need help?
Do you have a question about the End Panel and is the answer not in the manual?
Questions and answers