Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DOMAILLE ENGINEERING HDC-5200
Summary of Contents for DOMAILLE ENGINEERING HDC-5200
- Page 1 D o m a i l l e E n g i n e e r i n g L L C A P M M O D E L H D C - 5 2 0 0 P T I C A L I B E R O L I S H I N G A C H I N E...
-
Page 2: Table Of Contents
User Rights & Settings ................10 Process Setup ....................14 Inter-Machine Process Transfer ..............17 The APM HDC-5200 is designed to address the need to efficiently polish a large Deleting Processes .................... 18 volume of connectors while maintaining a consistent high level of quality. -
Page 3: Getting Started
Unpacking & Setup chine. Route Drain Hose to a collection container. NOTE: Due to the weight of the APM HDC-5200, it is recommended that 10. In order to raise and lower the Overarm, you must release the Over- two people lift it from the shipping case. - Page 4 Overarm Cable Management System APM HDC-5200 USER’S GUIDE Quick-Release Button D o m a i l l e E n g i n e e r i n g L L C Drip Tray Platen Drain Hose Fitting Step Start...
-
Page 5: Machine Setup
Plug the power cord into the back of the machine and into a properly grounded drive unit, thus causing failure. drive unit, thus causing failure. The APM HDC-5200 load cell has been calibrated at Domaille Engineering prior to outlet—100-240VAC, 50/60Hz. If your power cord is equipped with a large yellow ... - Page 6 To delete a pad name, highlight the name, then touch the “Delete” button. Process Variables: Setting & Copying/Backup Procedures Lubricant Settings: The APM HDC-5200 allows you to define valid variables that can be used in the defini- Select “Lubricant”, using the down arrow in the “Select Setting” box as necessary.
-
Page 7: User Rights & Settings
-5200 machines as well as providing backup and retrieval capability. per machine. A USB flash drive has been included with the shipment of your APM HDC-5200. When the “Password” box is blank, no password protection is in effect. To activate... - Page 8 APM HDC-5200 USER’S GUIDE APM HDC-5200 USER’S GUIDE D o m a i l l e E n g i n e e r i n g L L C D o m a i l l e E n g i n e e r i n g L L C...
-
Page 9: Process Setup
Touch the “Speed Ramp Up (Sec)” box to access the keypad. This feature The number of processes that can be defined and stored on the APM HDC-5200 is will slow start the platen. Enter the number of seconds desired from zero only limited by the amount of internal memory. -
Page 10: Inter-Machine Process Transfer
The maximum numeric input for the film change interval is 99. Select “OK”. The APM-HDC-5200 is equipped with a USB data storage slot. This feature allows machine-stored processes to be copied onto a USB data storage device, thus allow- 12. -
Page 11: Deleting Processes
APM HDC-5200 USER’S GUIDE APM HDC-5200 USER’S GUIDE D o m a i l l e E n g i n e e r i n g L L C D o m a i l l e E n g i n e e r i n g L L C... -
Page 12: Polishing Pad And Film Placement
APM HDC-5200 USER’S GUIDE D o m a i l l e E n g i n e e r i n g L L C APM HDC-5200 USER’S GUIDE D o m a i l l e E n g i n e e r i n g L L C... -
Page 13: Rework Start Step
Step box. The polishing process will automatically take you to the pre- defined rework start step and continue through each step until the final step in the The following procedure should be used to shut down the APM HDC-5200. process is complete. Upon completion, the program will return to step #1. -
Page 14: Daily
Disconnect the polishing machine from the power source before doing any maintenance work. Proper care and handling of the polishing fixtures and APM HDC-5200 machine is critical to maintain polishing accuracy. If the machine or polishing fixtures are damaged Polishing Machine Fan Filter in any way, contact Domaille Engineering for advice or repair. - Page 15 APM HDC-5200 USER’S GUIDE APM HDC-5200 USER’S GUIDE D o m a i l l e E n g i n e e r i n g L L C D o m a i l l e E n g i n e e r i n g L L C...
-
Page 16: Service & Support
D o m a i l l e E n g i n e e r i n g L L C Precautions CE Notice (European Union) For safe, effective operation of the APM-4000 Polishing Machine, please ob- Marking by the symbol CE indicates compliance of the APM HDC-5200 to serve the following: the following directives of the European Union: ... -
Page 17: Limited Warranty
If shipping the APM HDC-5200 for warranty repair, back up process data to the memory card, referring to User’s Guide for process transfer instructions. Remove and retain memory card, as Domaille will not accept liability for lost data. - Page 18 D o m a i l l e E n g i n e e r i n g L L C D o m a i l l e E n g i n e e r i n g L L C Domaille Engineering, LLC ...
Need help?
Do you have a question about the HDC-5200 and is the answer not in the manual?
Questions and answers